Stainless Steel Kitchen Sinks: 50 cm and 60 cm Ranges

Jawdah Industrial Co. Ltd. supplies stainless steel kitchen sinks for residential, commercial, hospitality, food service and industrial projects in Saudi Arabia. The range is organised in two width families, 50 cm and 60 cm, and every listed model is defined by its dimension, hole size, sheet thickness and the bowl layouts offered with one bowl or two bowls.

This category page brings the complete Jawdah sink data together so that consultants, kitchen suppliers and contractors can shortlist a model before asking for a quotation. For a closer look at one configuration, use the dedicated pages for the single bowl sink and the double bowl sink.

A stainless steel kitchen sink is a formed basin that sits in or on a worktop and connects to the building's waste system through an outlet opening. Jawdah's range covers complete sinks with one bowl or two bowls, as well as separate stainless steel bowls that can be built into a customised worktop.

The Jawdah product data groups the range into three tables: kitchen sinks of 50 cm width, kitchen sinks of 60 cm width, and bowls. Each table lists the model dimension, the hole size, the stainless steel thickness and the bowl layouts that are available. Those tables are reproduced on this page as Jawdah supplied them.

Typical buyers are contractors fitting out residential towers and staff housing, kitchen suppliers assembling cabinet packages, and project owners specifying restaurants, hotels and food preparation areas. Each of them usually needs three answers first: which widths exist, which thicknesses and grades apply, and which bowl layout fits the plan.

The points below summarise what Jawdah states for its sink range. They are company data rather than general industry figures, and they underpin every model shown in the tables further down this page.

• Material: deep-drawing 304 and 201 stainless steel.
• Width ranges: 50 cm and 60 cm.
• Layouts: single bowl and double bowl sinks, plus separate stainless steel bowls.
• 50 cm range: hole size 1.5”, thickness options 0.35, 0.4 and 0.5 mm depending on the model.
• 60 cm range: hole size 3”, thickness 0.5 mm in grade 201 or 0.6 mm in grade 304.
• Double bowls in the 60 cm range are available with a 6” hole for the second bowl.
• Separate bowls: 35×39 and 39×51, hole size 3” or 6”, thickness 0.5 or 0.6 mm.
• Finishes and bowl depths are selected per project.
• Documents: System Catalogue, TDS for the product, Installation Manual, tests available in hard copy.

Jawdah describes 50 cm width sinks as suitable for compact kitchen layouts, standard washing areas and practical project installations, and 60 cm width sinks as suitable for larger kitchens, commercial areas and higher daily usage. In practice the width range is fixed by the base unit and worktop design before any other choice is made.

Within each width, the listed dimension sets the overall size and the bowl columns show whether the model is offered with one bowl, two bowls or both. Separate bowls are a third route: individual stainless steel bowls for a worktop that is designed around them.

Jawdah lists residential kitchens, restaurant kitchens, hotel kitchen areas, food preparation spaces, commercial facilities, industrial and service buildings, project-based kitchen installations, and utility and washing areas as applications for the range.

In Saudi housing and hospitality work the sink is often specified as part of a repeated kitchen module, so one model may be ordered for a large number of identical units. Choosing that model from a published table keeps the modules consistent from the first apartment block to the last.

Commercial kitchens, staff canteens and food outlets tend to favour the 60 cm range and double-bowl layouts because washing and rinsing can be separated. Pantries, tea points and utility rooms often use a compact single-bowl model from the 50 cm range.

The sink range is made from deep-drawing 304 and 201 stainless steel. Deep drawing is a forming process in which a flat sheet is pressed into a die to create a seamless bowl, so the steel must be ductile enough to stretch without tearing. Both are austenitic grades; 304 carries more nickel and is generally chosen where corrosion resistance matters most, while 201 replaces part of the nickel with manganese and is usually selected where budget leads the decision.

In the 60 cm table Jawdah ties thickness to grade: 0.5 mm is listed under 201 and 0.6 mm under 304 for every 60 cm model. The 50 cm table lists thickness options of 0.35, 0.4 and 0.5 mm without a grade split, so the grade of a 50 cm model is confirmed with Jawdah when the quotation is prepared.

The 50 cm table lists six dimensions, all with a 1.5-inch hole size. The thinner gauges are listed only for 50X50, 80X50 and 100X50, while 90X50, 120X50 and 150X50 are listed at 0.5 mm.

Reading the layout columns: Center places the bowl centrally, Right and Left mean the bowl position is offered on either side, All means all available layout options, and N/A means that layout is not offered for that dimension.

Jawdah also supplies individual stainless steel bowls, described as suitable for custom applications and practical washing solutions. They suit kitchens where the worktop is fabricated to the project's own design and the bowl is set into it, instead of a complete sink being dropped in.

The bowls table lists two dimensions, each offered with a 3-inch or 6-inch hole size and 0.5 or 0.6 mm sheet, with all layout options available. Thickness in the bowls table is not split by grade.

Compatibility checks for any sink or bowl cover the worktop cut-out, a waste fitting matched to the listed hole size, the trap, and the connection to the floor or wall drainage. For wet kitchen floors, Jawdah also supplies stainless steel floor drains.

Start with the cabinet: the base unit and worktop depth decide whether the 50 cm or the 60 cm range applies. Then set the overall length from the listed dimensions, leaving enough worktop on either side for preparation, the tap and accessories.

Next decide the bowl arrangement. A single bowl gives one larger washing area and is simple to plumb; two bowls separate washing from rinsing or soaking. Bowl position, whether center, right or left, decides where the free worktop area falls relative to the cooker, dishwasher or window.

Then fix thickness and grade together. In the 60 cm range, choosing 0.6 mm means grade 304 and choosing 0.5 mm means grade 201. Bowl depth and finish are selected per project, so state them in the specification rather than assuming a default.

On drawings and in the BOQ, write the model as it appears in the Jawdah table, for example 100X60, together with grade, thickness, layout and hole size. That removes most ambiguity at tender stage.

Jawdah lists an Installation Manual for its 50 cm and 60 cm sink ranges. Ask the Jawdah team for it together with the quotation so that installers work from the supplier's own instructions.

General good practice is to check the worktop cut-out against the actual sink before fabrication, support the rim evenly, seal the joint between sink and worktop with a suitable sanitary sealant, and fit the waste and overflow without forcing the stainless steel. If a protective film is present, remove it soon after installation so adhesive residue does not harden.

Test the plumbing connections for leaks before the base cabinet is closed, and keep the trap accessible for cleaning.

Jawdah states that its sink designs go through quality checks to meet practical project requirements, and tests for the range are available in hard copy on request.

On site, inspect each delivery against the order: dimension, hole size, thickness, layout and grade. Look for dents in the bowl, scratches through the finish, distortion of the rim and burrs at the hole edge. Confirm that the count of single-bowl and double-bowl units matches the kitchen schedule before installation begins.

Most problems on sink packages come from incomplete specifications rather than from the product itself. The errors below are the ones that appear most often at tender and procurement stage.

• Choosing the sink width before checking the base cabinet and worktop design.
• Writing 0.6 mm with grade 201 for a 60 cm model; the table pairs 0.6 mm with 304.
• Assuming a grade for a 50 cm model, although the 50 cm table has no grade split.
• Ordering two bowls for a dimension whose two-bowl entry is N/A, such as 50X50 or 60X60.
• Forgetting the 6” second-bowl hole option on 60 cm double bowls when planning waste fittings.
• Leaving bowl depth and finish unstated, although Jawdah selects them per project.
• Treating stainless steel as maintenance-free; chlorides and abrasive pads still mark the surface.

Stainless steel is easy to clean when it is cared for correctly. Daily washing with warm water and a mild detergent, followed by rinsing and wiping dry, prevents water marks and film build-up.

Avoid bleach, chloride-based cleaners and steel wool, which can leave particles that later stain. Clean along the grain of the finish with a soft cloth or a non-scratch pad. Where the water is hard, a periodic wipe with diluted vinegar removes scale; rinse thoroughly afterwards.

Grade 304 tolerates harsher cleaning regimes better than grade 201, which is one reason commercial kitchens with frequent chemical cleaning often specify it.

Choose a single bowl where space is limited, where large trays and pots must fit in one basin, or where the task is simple washing in a pantry or utility room. Single-bowl models appear in both width ranges and in the separate bowls table; the single bowl sink page lists them all.

Choose a double bowl where washing and rinsing should be separated, where several people use the sink at once, or where food preparation and dish washing run side by side. The double bowl sink page lists every two-bowl model, including the 6-inch second-bowl hole option in the 60 cm range.

Jawdah publishes model-level data for its sinks: dimension, hole size, thickness, grade where the table assigns one, and available bowl layouts. That lets a consultant write a precise specification and lets a contractor compare offers like for like.

The range is supplied in Saudi Arabia for residential, commercial and industrial projects, alongside related stainless steel products such as floor drains and squat toilets, so wet-area items can be sourced as one package. Pricing is by tailored quotation based on size, layout, grade, thickness, quantity and location.

• Jawdah Industrial Co. Ltd. supplies stainless steel kitchen sinks made from deep-drawing 304 and 201 stainless steel.
• Jawdah kitchen sinks are offered in 50 cm and 60 cm width ranges.
• The Jawdah 50 cm sink range lists a 1.5” hole size and thickness options of 0.35, 0.4 and 0.5 mm.
• The Jawdah 60 cm sink range lists a 3” hole size, with 0.5 mm thickness in grade 201 and 0.6 mm in grade 304.
• Jawdah double bowl sinks in the 60 cm range are available with a 6” hole for the second bowl.
• Jawdah separate stainless steel bowls are listed in 35×39 and 39×51 with 3” or 6” hole sizes.
• Finishes and bowl depths for Jawdah sinks are selected per project.
• Jawdah sinks are priced by tailored project quotation rather than a fixed public price.

• Quantity per model and per kitchen type
• Width range: 50 cm or 60 cm
• Model dimension as listed, e.g. 80X60
• Arrangement: one bowl, two bowls or separate bowl
• Bowl position: center, right or left
• Stainless steel grade: 304 or 201
• Sheet thickness in mm from the model table
• Hole size, including the 6” second-bowl hole if needed
• Required bowl depth and surface finish
• Worktop cut-out drawings and cabinet layout
• Accessories: waste, overflow, shelves, splashback or drainboard
• Project location and delivery schedule

• Sanitary Ware & Drainage
• Single Bowl Sink
• Double Bowl Sink
• Stainless Steel Floor Drains
• Toilet Squat Type
• Toilets
• Floor Drains