Toilets · Squat Type
Stainless Steel Squat Toilet (Arabic Type), 62X64
The Jawdah Toilet Squat Type is a stainless steel squat pan made from deep-drawing 304 stainless steel, listed at dimension 62X64 with a 4” hole size and 1 mm sheet thickness, for commercial, industrial, public and high-traffic facilities.
Jawdah Industrial Co. manufactures stainless steel squat toilets made from deep-drawing 304 stainless steel. They are designed for commercial, industrial, public and high-traffic facilities that need durable and easy-to-clean sanitary fixtures, and they come in different designs to meet Saudi market requirements.
This page gives the published squat toilet data, explains how a stainless steel squat pan is built and installed, and lists what to include in an RFQ. For the full toilet range and the choice between squat and WC types, see the Toilets category.
- Dimension62X64
- Hole size4”
- Thickness1 mm
Quick answer
The Jawdah stainless steel squat toilet is a floor-level squat pan deep-drawn from grade 304 stainless steel. It is listed at dimension 62X64 with a 4-inch hole size and 1 mm stainless steel thickness, with a stainless steel top and slots design. It suits factories, schools, public facilities, industrial sites and commercial buildings where durability and easy cleaning matter.
What a stainless steel squat toilet is
A squat toilet, known in Saudi Arabia as the Arabic toilet, is a pan set level with the floor on which the user squats rather than sits. It has a bowl area that leads to an outlet, raised or textured foot areas on each side, and a flushing water supply that rinses the bowl into the drainage line.
Made in stainless steel instead of ceramic, the pan resists impact, does not craze or chip, and can be scrubbed and disinfected many times a day. That is why stainless steel squat pans are common in public washrooms, factories, labour accommodation, schools and other facilities with constant use.
Jawdah squat toilet facts
The data below is taken directly from the Jawdah product information for the squat toilet.
- Material: deep-drawing 304 stainless steel.
- Dimension: 62X64.
- Hole size: 4”.
- Stainless steel thickness: 1 mm.
- Design entry: stainless steel top and slots; further designs confirmed on request.
- Designed for commercial, industrial, public and high-traffic facilities.
- Available in different designs to meet Saudi market requirements.
- Documents: System Catalogue, Stainless Steel Squat Toilets Technical Data Sheet, tests available in hard copy.
Anatomy of the pan
A deep-drawn squat pan is pressed from a single stainless steel blank, so the bowl, the surrounding deck and the outlet collar form one continuous surface. With no welded joints in the wetted area, there are fewer places for dirt and bacteria to lodge.
Jawdah lists the pan with a 1 mm stainless steel thickness, which gives the stiffness needed for a fixture that carries a user's full weight on its deck. The 4-inch hole is the opening through which the pan discharges to the soil connection beneath the floor.
How flushing and drainage work
Water from a flush valve or a cistern enters at the rear of the pan and sweeps the bowl towards the outlet. Waste then passes through a water-seal trap, either below the pan or built into the drainage design, which stops sewer gases entering the room.
Because the pan sits in the floor, the trap and the soil branch are usually set in the slab or in a raised floor build-up. Coordinating these levels before the floor is poured or screeded is the single most important step in a squat toilet installation.
Where the Jawdah squat toilet is used
Jawdah lists factories, public facilities, schools, industrial sites, commercial buildings and projects that require strong and hygienic sanitary products as typical uses.
In practice that covers washroom blocks in industrial cities and warehouses, mosques and ablution areas, petrol and service stations, labour camps and staff housing, transport terminals, and the public toilets of malls and government buildings across the Kingdom.
Why grade 304 matters in a washroom
Grade 304 is the standard austenitic stainless steel for sanitary and food-contact equipment. Its chromium content forms a thin passive film that protects against water and moisture, and Jawdah notes that 304 stainless steel helps resist corrosion and moisture, which suits sanitary areas exposed to water and frequent cleaning.
The passive film repairs itself in air, but it can be damaged by strong chlorides. Cleaning teams should therefore avoid leaving chlorine bleach or acidic descalers on the pan for long periods.
Squat toilet specification table
The Jawdah table lists one dimension for the stainless steel squat toilet. Write it into drawings and BOQs exactly as shown, together with hole size, thickness and the required design.
| Dimension | Hole size | SS thickness (mm) | Design | Material |
|---|---|---|---|---|
| 62X64 | 4” | 1 | Stainless steel top and slots | Deep-drawing 304 stainless steel |
Further design options and the full data are in the Stainless Steel Squat Toilets Technical Data Sheet, requested from Jawdah.
Design and detailing tips
Allow a cubicle large enough for the 62X64 pan plus comfortable foot and door clearance, and position the pan so the user faces the door or a side wall according to local practice and the operator's preference.
Fall the surrounding floor gently towards the pan or towards a separate stainless steel floor drain, so that washing water does not pond. Provide a hand-held spray or bidet hose and a tap where the operator requires them, and plan the flush valve or cistern position with the plumbing engineer.
Installation sequence
Set the soil branch and trap at the correct level, connect the pan's 4-inch outlet, then bed the pan fully on mortar or the method stated in the Jawdah documents so the deck is supported across its whole area. Check that the deck finishes flush with the planned tile level.
Test the connection with water before tiling, then tile up to the pan edge and seal the joint with a flexible sanitary sealant. Finally test flushing under real flow and confirm there are no leaks at the outlet.
Quality checks on delivery and handover
Check each pan against the order for dimension, hole size, thickness and design. Inspect the deck and bowl for dents, deep scratches or burrs at the hole edge. If the consultant requires test evidence, request the tests that Jawdah keeps available in hard copy.
Selection mistakes to avoid
These are the usual errors on squat toilet packages.
- Pouring the slab before confirming the pan, trap and soil levels.
- Specifying a squat pan without stating the required design.
- Leaving out a floor drain in washrooms that are hosed down.
- Using a soil fitting that does not match the 4” hole size.
- Bedding the pan on spot fixings so the deck flexes under load.
Daily cleaning and long-term care
Jawdah describes its squat toilets as easy to clean and maintain, with a practical surface that reduces maintenance effort in public and high-traffic facilities. Daily cleaning with a neutral sanitary detergent and a soft brush, followed by a water rinse, keeps the surface hygienic.
Remove limescale periodically with a cleaner suitable for stainless steel, and never use steel wool, which leaves iron particles that cause rust-coloured spots.
Squat type or western WC
The squat pan has no seat to clean and suits users who prefer the Arabic type, which makes it efficient in high-traffic public blocks. A western WC toilet is needed where seated use or accessibility is required. Many Saudi facilities combine both types in one washroom.
Why choose the Jawdah squat toilet
Jawdah publishes a clear specification for its squat toilet, offers it in deep-drawing 304 stainless steel, and supports submittals with a System Catalogue, a Technical Data Sheet and hard-copy tests. The same supplier also provides stainless steel floor drains and kitchen sinks for the rest of the wet-area package.
Key facts
- The Jawdah stainless steel squat toilet is made from deep-drawing 304 stainless steel.
- The Jawdah squat toilet is listed at dimension 62X64.
- The Jawdah squat toilet has a 4” hole size and a stainless steel thickness of 1 mm.
- The published design entry for the Jawdah squat toilet is a stainless steel top with slots.
- Jawdah squat toilets are designed for commercial, industrial, public and high-traffic facilities.
- Jawdah provides a System Catalogue, a Technical Data Sheet and hard-copy tests for its squat toilets on request.
RFQ / BOQ checklist
- Quantity of squat toilets per washroom block
- Dimension 62X64 and design required
- Hole size 4” and soil pipe connection detail
- Stainless steel thickness: 1 mm as listed
- Flushing method: flush valve or cistern
- Trap arrangement and floor build-up depth
- Associated floor drains and spray hose points
- Documents needed for submittal
- Delivery location and installation phasing
Closer look
18–20In preparation
Further chapters in preparation
These parts of the product page are being prepared with the Jawdah technical team and will be published once verified.
Technical resources
Technical documentation is being prepared for this product.
Projects using this product
Project references are being prepared.
Compatible systems
System relationships for this product are being prepared.
Our technical team can share the current information on request.
Ask the technical teamFrequently asked questions
What size is the Jawdah stainless steel squat toilet?
The squat toilet is listed at dimension 62X64, with a 4-inch hole size and 1 mm stainless steel thickness.
Which stainless steel grade is used for the squat toilet?
Jawdah makes its squat toilets from deep-drawing 304 stainless steel, which helps resist corrosion and moisture in wet, frequently cleaned areas.
What design options are available?
The published design entry is a stainless steel top with slots. Jawdah states the squat toilets come in different designs, so confirm any further options with the team.
Where is the squat toilet typically installed?
Jawdah lists factories, public facilities, schools, industrial sites and commercial buildings, and the pan suits other high-traffic washrooms.
Does the squat toilet include a trap?
Trap and flushing arrangements are not stated in the published table. Ask Jawdah for the Technical Data Sheet and plan the trap with the drainage design.
Which documents can I request?
Jawdah lists a System Catalogue, a Stainless Steel Squat Toilets Technical Data Sheet and tests available in hard copy. Request them from the Jawdah team.
How is the squat toilet installed?
The pan is set flush with the finished floor, its 4-inch outlet connected to the soil branch, fully bedded so the deck is supported, then tiled around and sealed.
How do I clean a stainless steel squat toilet?
Use a neutral sanitary detergent and soft brush, rinse with water, descale periodically with a stainless-safe cleaner, and avoid bleach left on the surface and steel wool.
21Next step
Request squat toilets for your project
Send quantities, required design and drainage details. Jawdah will share the Technical Data Sheet and prepare a quotation for your washroom blocks.