L-Angle · 24
L-Angle 24 – Ceiling Metal Profile
L-Angle 24 is the larger of Jawdah's two wall angles, a 24x24 mm galvanised steel section that edges a suspended gypsum ceiling at the wall.
- Size
- 24
- Section
- 24x24 mm
- Material
- Galvanised steel
- Length
- 3000 mm
Overview
Quick answer
Jawdah's L-Angle 24 is a perimeter profile for suspended gypsum ceilings with a 24x24 mm section listed in the drywall suspension datasheet. It is screwed to the walls at ceiling level and is the larger of the two listed L-angle sizes. The steel is hot-dip galvanised to ASTM A653M, 0.35 up to 0.9 mm, in 3000 mm lengths.
Overview
About L-Angle 24 – Ceiling Metal Profile
When the ceiling edge detail shows a 24x24 mm angle, this is the profile to order. It is the larger of the two L-Angles Jawdah lists, a couple of millimetres wider per leg than size 22, and like that sibling its section is published in the datasheet. It is fixed along the walls at ceiling height to carry and finish the ceiling perimeter.
In the ceiling system, L-Angle 24 sits at the walls. It is fixed around the room at the finished ceiling level, giving the board edge and grid ends a line to meet.
The datasheet lists a 24x24 mm L-angle section, which corresponds to size 24. Its sibling, size 22, has a 22x22 mm section; otherwise their recorded data is the same. Steel is hot-dip galvanised to ASTM A653M, from 0.35 up to 0.9 mm, with other thicknesses on request, and the standard length is 3000 mm.
Fire and humidity data in the datasheet describe the raw material only: BS 476 Part 6 – 1989, a Class 1 surface flame spread to BS 476 Part 7 – 1997, and EN ISO 6270-2. They are not a classification of the finished ceiling.
Go with size 24 if the specification calls for a 24x24 mm angle, or if you want the larger of the two listed sections. Size 22 is the alternative at 22x22 mm. If the detail needs a W-shaped edge instead, look at the W-Angle. Confirm steel thickness and lengths with Jawdah.
Types
Sizes and variants
This page is the 24 size.
Other l-angle sizes: L-Angle 22.
Applications
Where it is used
The datasheet lists the profiles for the installation of gypsum plasterboard. The l-angle is used in:
- Wall-fixed edge of suspended gypsum ceilings detailed with a 24x24 mm angle
- Perimeter support for drywall bulkheads that run into a wall
- Edge line for ceilings finished in Jawdah gypsum boards
Installation
Installation notes
The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:
- Store profiles flat and dry, away from site water
- Wear eye protection when cutting metal
- Use profiles and accessories from the same system
Technical
Closer look
Detailed product imagery is being prepared.
In preparationSpecifications
Technical data
Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.
| Property | Value | Source |
|---|---|---|
| Size (product list) | 24 | Jawdah product list |
| Section (datasheet) | 24x24 mm | Datasheet |
| Steel thickness | 0.35 up to 0.9 mm; other thicknesses on request | Datasheet |
| Material | Hot-dip galvanised steel complying with ASTM A653M | Datasheet |
| Standard length | 3000 mm | Datasheet |
| Fire (raw material) | BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997 | Datasheet |
| Humidity (raw material) | According to EN ISO 6270-2 | Datasheet |

Key facts
- L-Angle 24 is listed under Jawdah Drywall Solutions, Ceiling Metal Profiles.
- Role: the perimeter member fixed to the walls at ceiling level.
- Datasheet section for this size: 24x24 mm.
- Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
- Other sizes listed: 22.
RFQ / BOQ checklist
- Profile and size (L-Angle 24)
- Steel thickness
- Length and quantity
- Board type and layers the system carries
- Accessories needed (clips, rods, anchors, screws)
- Project location and delivery date
Resources
Further chapters in preparation
Technical resources
Technical documentation is being prepared for this product.
Projects using this product
Project references are being prepared.
Compatible systems
Information on compatible systems for this product is being prepared.
Our technical team can share the current information on request.Ask the technical team
FAQ
Frequently asked questions
The datasheet lists a 24x24 mm section for size 24. The standard length is 3000 mm.
When the ceiling detail or specification shows a 24x24 mm angle, or you want the larger of the two listed L-angle sections. Size 22 has a 22x22 mm section.
The datasheet gives 0.35 up to 0.9 mm and says other thicknesses are available on request, so state your requirement when asking Jawdah for a quotation.

Next step
Request a quotation for L-Angle 24
Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.
