Jawdah Industrial Co. Ltd.

W-Angle · 20x20

W-Angle 20x20 – Ceiling Metal Profile

W-Angle 20x20 is the smaller of Jawdah's two W-angle sizes, a galvanised perimeter angle used at the edges of a suspended gypsum ceiling.

Size
20x20
Material
Galvanised steel
Length
3000 mm

Overview

Quick answer

Jawdah's W-Angle 20x20 is a hot-dip galvanised steel perimeter angle for the edges of suspended gypsum ceilings. It is the smaller of the two listed sizes, 20x20 and 25x25. The datasheet gives steel from 0.35 up to 0.8 mm and a 3000 mm standard length, but no section for 20x20, so Jawdah confirms its dimensions on request.

Overview

About W-Angle 20x20 – Ceiling Metal Profile

The 20x20 W-Angle is the compact option in a pair whose other member is 25x25. Both edge the ceiling at the wall with a W-shaped section, but only the larger size appears in the datasheet. For 20x20, the material, steel range and length are recorded, while the section itself is confirmed by Jawdah before you order.

W-Angle 20x20 is a perimeter angle used at the edges of the ceiling, in place of an L-Angle where the detail calls for a W-shaped edge. It is listed on Jawdah's product list alongside the larger 25x25 size.

The supplied datasheet lists W-angle sections of 25x25x25x25 mm and names none of them as 20x20. The section of this size is therefore not specified, and Jawdah confirms it on request rather than scaling it from the larger size.

What is recorded applies to both W-angle sizes: hot-dip galvanised steel complying with ASTM A653M, 0.35 up to 0.8 mm thick, in 3000 mm standard lengths. The raw-material data cites BS 476 Part 6 – 1989, Class 1 surface flame spread under BS 476 Part 7 – 1997, and humidity per EN ISO 6270-2.

Choose 20x20 when the ceiling edge detail shows the smaller W-angle. If you need a section that is already in the datasheet, the 25x25 size is covered there; 20x20 is not. Confirm the 20x20 section with Jawdah, and note that the steel range for W-angles ends at 0.8 mm.

Types

Sizes and variants

This page is the 20x20 size.

Other w-angle sizes: W-Angle 25x25.

Applications

Where it is used

The datasheet lists the profiles for the installation of gypsum plasterboard. The w-angle is used in:

  • Perimeter edges of suspended gypsum ceilings detailed with a 20x20 W-angle
  • Edges of ceiling bulkheads and level changes framed in drywall
  • Wall junctions of ceilings finished with Jawdah gypsum boards

Installation

Installation notes

The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:

  • Store profiles flat and dry, away from site water
  • Wear eye protection when cutting metal
  • Use profiles and accessories from the same system

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

W-Angle 20x20 – Ceiling Metal Profile: recorded data
PropertyValueSource
Size (product list)20x20Jawdah product list
Section (datasheet)Not specified in the supplied datasheetDatasheet
Steel thickness0.35 up to 0.8 mmDatasheet
MaterialHot-dip galvanised steel complying with ASTM A653MDatasheet
Standard length3000 mmDatasheet
Fire (raw material)BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997Datasheet
Humidity (raw material)According to EN ISO 6270-2Datasheet

Key facts

  1. W-Angle 20x20 is listed under Jawdah Drywall Solutions, Ceiling Metal Profiles.
  2. Role: a perimeter angle used at the edges of the ceiling.
  3. Section for this size: not specified in the supplied datasheet.
  4. Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
  5. Other sizes listed: 25x25.

RFQ / BOQ checklist

  • Profile and size (W-Angle 20x20)
  • Steel thickness
  • Length and quantity
  • Board type and layers the system carries
  • Accessories needed (clips, rods, anchors, screws)
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • No. It lists a 25x25x25x25 mm W-angle section, which belongs to the 25x25 size. The 20x20 section is confirmed by Jawdah on request.

  • The datasheet gives 0.35 up to 0.8 mm hot-dip galvanised steel complying with ASTM A653M for W-angles.

  • Yes. Jawdah's product list gives two W-angle sizes, 20x20 and 25x25, and 20x20 is the smaller.

Next step

Request a quotation for W-Angle 20x20

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.