Jawdah Industrial Co. Ltd.

Ceiling Accessories · Anchor Bolt

Anchor Bolt for Suspended Ceiling Hangers

The Jawdah anchor bolt is a Ø6 mm galvanised steel fixing that secures the top of a ceiling rod hanger into the structural soffit.

Diameter
Ø6 mm
Material
Galvanised steel
Holds
Top of the rod hanger

Overview

Quick answer

A ceiling anchor bolt fixes the top of a suspension hanger into the slab or structure above. Jawdah lists it in galvanised steel at Ø6 mm. The T-Grid, gypsum tile and Standard Clip-In data sheets name anchor bolts with rod hangers and adjustment clips as suspension accessories. Holding capacity is not published, so confirm the fixing for your soffit.

Overview

The fixing at the top of the chain

It is the first part installed and the one every other hanging part depends on. Its suitability depends on the soffit it goes into, so tell the Jawdah team what the structure is made of before you order.

A suspended ceiling hangs from hundreds of points, and each starts with a fixing in the structure. On Jawdah T-Grid, gypsum tile and Standard Clip-In ceilings, that fixing is the anchor bolt. It is set into a drilled hole in the soffit and provides the point from which the rod hanger drops to the grid.

The anchor bolt carries the whole share of ceiling weight assigned to its hanging point, so the quality of the hole and the condition of the substrate matter as much as the part itself. An anchor set in a cracked or hollow zone, or in a hole drilled to the wrong size, is the most common reason a hanging point loosens over time. The anchor bolt is one of the seven items in the Ceiling Accessories item list.

Applications

Systems that list anchor bolts

The data sheets for the T-Grid system, plain gypsum ceiling tiles and acoustical perforated gypsum tiles list anchor bolts with rod hangers and adjustment clips as suspension accessories. The Clip-In system data sheet lists the same three for its Standard set. The Advanced Clip-In set lists a drop anchor, which receives threaded rod.

Installation

Setting anchor bolts

As general practice, mark hanging points from the ceiling layout, check the soffit for embedded services and post-tension zones with the structural engineer, then drill to the size the anchor requires for a Ø6 mm fixing. Clean the hole before setting the anchor. Attach the rod hanger so it hangs plumb, then fit the adjustment clip. If a hole hits reinforcement or a void, move the point and record the change.

Selection pitfalls

Anchor bolt mistakes

Fixing problems are hard to reach once the ceiling is closed.

  • Anchors ordered without stating the soffit type
  • Holes drilled oversize or left full of dust
  • Anchors set in cracked or hollow zones
  • Anchor bolts ordered for an Advanced Clip-In ceiling that needs drop anchors

Choosing

When to order this item

Order one anchor bolt per rod hanger on T-Grid, gypsum tile and Standard Clip-In ceilings. Tell the Jawdah team the soffit type, such as concrete slab or steel deck, so the fixing can be confirmed. For threaded rod ceilings in the Advanced Clip-In set, order the drop anchor instead.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Jawdah data

Recorded data for the anchor bolt

The Jawdah ceiling accessories list records material and diameter. The anchor type, length and holding capacity are not published.

Anchor bolt: recorded data
PropertyValue
MaterialGalvanised steel
DiameterØ6 mm
Length and anchor typeNot specified in the supplied data sheet
Holding capacityNot specified in the supplied data sheet
Suitable substratesNot specified in the supplied data sheet

Comparison

Anchor bolt or drop anchor?

Both are Ø6 mm soffit fixings in the Jawdah list. The difference is the hanger they receive and the system set they belong to.

The two soffit fixings in the Jawdah list
PointAnchor boltDrop anchor
Recorded sizeØ6 mmØ6 mm
ReceivesRod hangerThreaded rod
Paired withAdjustment clipGalvanized nut, Omega clip
System setT-Grid, gypsum tiles, Clip-In StandardClip-In Advanced

Key facts

  1. The Jawdah ceiling anchor bolt is galvanised steel, Ø6 mm.
  2. It fixes the top of a rod hanger into the structural soffit.
  3. T-Grid, gypsum tile and Standard Clip-In data sheets list anchor bolts as suspension accessories.
  4. Advanced Clip-In ceilings use a drop anchor with threaded rod instead.
  5. Anchor bolt holding capacity and suitable substrates are not published in the supplied data.

RFQ / BOQ checklist

  • Suspension system and Clip-In set
  • Number of hanging points
  • Soffit type and condition
  • Anchor bolt quantity
  • Matching rod hangers and adjustment clips
  • Delivery location

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • The Jawdah ceiling accessories list records it at Ø6 mm in galvanised steel.

  • It fixes into the soffit and holds the top of a rod hanger, which then carries the grid through an adjustment clip.

  • The T-Grid, plain gypsum tile, acoustical perforated gypsum tile and Standard Clip-In data sheets list anchor bolts as suspension accessories.

  • No. Both are Ø6 mm soffit fixings, but the drop anchor receives threaded rod in the Advanced Clip-In set, while the anchor bolt holds rod hangers.

  • Holding capacity is not specified in the supplied data and depends on the soffit. Confirm it with the Jawdah team and the structural engineer.

  • Suitable substrates are not published. State the soffit type in your RFQ so the Jawdah team can confirm the fixing.

Next step

Confirm anchors for your soffit

Send the soffit type, number of hanging points and suspension system. The Jawdah team will confirm anchors, hangers and clips for your quotation.