Jawdah Industrial Co. Ltd.

Ceiling Accessories · Rod Hanger

Rod Hanger for Suspended Ceiling Accessories

The Jawdah rod hanger is the galvanised steel wire rod, Ø3.8 mm and 0.5 to 2 m long, that drops from the structural soffit to the ceiling grid.

Diameter
Ø3.8 mm
Length
0.5 to 2 m
Material
Galvanised steel

Overview

Quick answer

A ceiling rod hanger is the vertical wire rod that carries a suspended ceiling grid from the slab. Jawdah lists it in galvanised steel at Ø3.8 mm in lengths from 0.5 to 2 m. The T-Grid, gypsum tile and Standard Clip-In data sheets name rod hangers, adjustment clips and anchor bolts as their suspension accessories.

Overview

What the rod hanger does

It is the vertical link of the standard hanging chain: an anchor bolt holds its top, an adjustment clip sets the grid height on it, and the grid hangs below. Choose the length from the depth of the ceiling void.

Every hanging point of a suspended ceiling needs a vertical member between the structure and the grid. On Jawdah T-Grid, gypsum tile and Standard Clip-In ceilings, that member is the rod hanger: a straight galvanised steel wire rod whose top is fixed to the soffit and whose lower end passes through an adjustment clip connected to the main runner or channel.

Because the hanger works in tension, its job is simple but it repeats hundreds of times on a large ceiling. A hanger that is too short cannot reach the grid, one that is far too long leaves a loose tail in the plenum, and a bent or inclined hanger pulls the grid sideways. Ordering the right length per zone is therefore the main decision on this item. The rod hanger is one of the seven items in the Ceiling Accessories item list.

Applications

Systems that use rod hangers

The technical data sheets for the T-Grid system, plain gypsum ceiling tiles and acoustical perforated gypsum tiles list rod hangers, adjustment clips and anchor bolts as suspension accessories. The Clip-In system data sheet lists the same three for its Standard set. The Advanced Clip-In set uses threaded rod instead.

Installation

Installation notes

As general practice, mark hanging points from the reflected ceiling plan, fix the anchor bolts, then attach the hangers so they hang plumb. Thread each hanger through an adjustment clip on the runner and level the grid before tiles go in. Where ducts block a hanging point, bridge the obstruction rather than hanging from the duct. Hanger spacing comes from the suspension system data.

Selection pitfalls

Common rod hanger mistakes

These errors usually show up at grid levelling, when they cost time to fix.

  • One length ordered for a plenum that changes depth
  • Hangers installed out of plumb around services
  • Fewer adjustment clips than hangers in the order
  • Rod hangers used on an Advanced Clip-In ceiling designed for threaded rod

Choosing

When to order this item

Order rod hangers for T-Grid, gypsum tile and Standard Clip-In ceilings, one per hanging point, grouped by length from 0.5 to 2 m to match the plenum depth in each zone. Order the same number of adjustment clips and anchor bolts. For deeper voids or Advanced Clip-In ceilings, see the threaded rod.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Jawdah data

Recorded data for the rod hanger

The Jawdah ceiling accessories list records material, diameter and length range. Other properties are not published and are listed as open points.

Rod hanger: recorded data
PropertyValue
MaterialGalvanised steel
DiameterØ3.8 mm
Length0.5 to 2 m
Load capacityNot specified in the supplied data sheet
Zinc coating massNot specified in the supplied data sheet

Comparison

Rod hanger or threaded rod?

Both are hangers, but they belong to different sets. Use the comparison to check which one your ceiling system calls for.

Rod hanger compared with threaded rod
PointRod hangerThreaded rod
Recorded sizeØ3.8 mm x 0.5 to 2 mØ6 mm x 3 m
Top fixingAnchor boltDrop anchor
Height adjustmentAdjustment clipGalvanized nut on the thread
System setT-Grid, gypsum tiles, Clip-In StandardClip-In Advanced

Key facts

  1. The Jawdah rod hanger is galvanised steel, Ø3.8 mm, in lengths from 0.5 to 2 m.
  2. Rod hangers are used with adjustment clips and anchor bolts.
  3. T-Grid, plain gypsum tile and acoustical perforated gypsum tile data sheets list rod hangers as suspension accessories.
  4. The Standard Clip-In set uses rod hangers; the Advanced set uses threaded rod.
  5. Rod hanger load capacity is not published in the supplied data.

RFQ / BOQ checklist

  • Suspension system and Clip-In set
  • Number of hanging points
  • Plenum depth per zone
  • Rod hanger lengths and quantities
  • Matching adjustment clips and anchor bolts
  • Soffit type
  • Delivery location

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • The Jawdah ceiling accessories list records it at Ø3.8 mm, in lengths from 0.5 to 2 m.

  • Galvanised steel. Jawdah states that its steel ceiling accessories are produced from hot-dip galvanised steel for rust and humidity resistance.

  • An anchor bolt fixes its top to the soffit and an adjustment clip connects it to the grid and sets the height.

  • Yes, on the Standard Clip-In set, which lists rod hangers, adjustment clips and anchor bolts. The Advanced set uses threaded rod.

  • Spacing is set by the suspension system data and the ceiling layout, not by the accessory list. Ask the Jawdah team for the system data.

  • Load capacity is not specified in the supplied data. Confirm it with the Jawdah team before designing heavy fittings onto the ceiling.

Next step

Order rod hangers by length

Send the ceiling layout and plenum depths. The Jawdah team will confirm hanger lengths, clips and anchors for your quotation.