Jawdah Industrial Co. Ltd.

Sandwich Panel Accessories · Fasteners

Pop Rivets for Sandwich Panel Flashings and Trims

Pop Rivets are the blind rivets in the Jawdah sandwich panel accessories range, used to join thin metal to thin metal, such as flashing laps, gutter joints and trims, working from one side only.

Role
Joins flashing laps and trims
Type
Blind rivet, set from one side
Size and material
Confirmed per project
Pop rivet, aluminium blind rivet for joining flashings to sandwich panels

Overview

Quick answer

A pop rivet, or blind rivet, is a tubular rivet with a mandrel through its centre. It is pushed into a drilled hole and the mandrel is pulled with a rivet tool, which expands the far end and clamps the sheets together before the mandrel snaps off. On sandwich panel buildings it joins flashing laps, gutter joints and trims. Jawdah supplies pop rivets as accessories; sizes and materials are confirmed per project.

Overview

What pop rivets do on a panel building

Flashings and gutters are made from lengths that overlap, and those laps need a small, tight fixing that does not reach the structure. A pop rivet sets from the outside with a hand tool. Jawdah lists it as an accessory and confirms size and material per project.

Panels are fixed to the steel with screws, but the formed flashings, cappings and gutters around them also have to be joined to each other along their laps. These joints are sheet to sheet, often with nothing solid behind them, so a screw has little to grip. A pop rivet solves this: it clamps the two sheets between its head and the expanded tail, and needs access from one side only.

Rivets give a neat, low-profile head on visible trims, which is why they are common on Wall Flashings, corner details and gutter joints, normally with a sealant line in the lap.

How it works

How a blind rivet sets

The rivet has two parts: a hollow body with a flanged head, and a steel mandrel through the middle. The installer drills a hole through both sheets, inserts the rivet and grips the mandrel with the rivet tool. As the tool pulls, the mandrel head is drawn into the body, swelling it on the blind side until the sheets are clamped. At a set force the mandrel breaks, leaving a closed joint. Sealed or closed-end rivets are used where water must not pass through the centre.

Applications

Choosing rivet material and grip

Grip range must suit the total thickness of the sheets being joined, including any sealant; a rivet with too short a grip will not clamp, and one with too long a grip will not set tightly. Rivet material should be compatible with the flashing and panel facing: where facings are aluminium or stainless steel, use a matching rivet to avoid galvanic corrosion. For visible trims, agree the head colour with the flashing colour.

Installation

Setting pop rivets well

Drill the hole to the size the rivet requires and remove burrs and swarf. Apply the lap sealant first, insert the rivet, hold the tool square to the sheet and pull until the mandrel breaks. Space rivets evenly along the lap so it closes without waves. Clean drilling swarf from the surfaces the same day, because it rusts and stains the coating.

Selection pitfalls

Rivet mistakes to avoid

These are the usual causes of loose or leaking laps.

  • Oversized holes that let the rivet spin
  • Grip range wrong for the joint thickness
  • Open-core rivets in a joint that must keep water out
  • Rivet metal incompatible with the facing
  • Laps riveted without sealant

Choosing

Ordering pop rivets

Estimate rivet numbers from the total length of flashing and gutter laps and the spacing you will use. Send this with the flashing schedule and facing material; the Jawdah team confirms the rivet size and material and lists it with the Self Drilling Screw, sealants and other accessories.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Specifications recorded for this item

Jawdah lists Pop Rivets by name in its sandwich panel accessories range. No diameter, grip range, body material or head colour is published, so the table shows what is confirmed per project.

Pop Rivets: published data
PropertyJawdah data
ItemPop Rivets (accessory of the sandwich panel range)
Diameter and grip rangeNot published; confirmed per project
Body and mandrel materialNot published; confirmed per project
Head finish or colourNot published; confirmed per project

Comparison

Pop rivet or self drilling screw?

The two fixings do different jobs. The comparison is general guidance.

Pop rivets compared with self drilling screws (general guidance)
QuestionPop RivetsSelf Drilling Screw
JoinsSheet to sheet (laps, trims, gutters)Panel or flashing to support steel
Needs a pre-drilled holeYesNo
RemovableOnly by drilling outYes, by unscrewing

Key facts

  1. Pop Rivets are listed in the Jawdah sandwich panel accessories range.
  2. A pop rivet is a blind rivet set from one side with a rivet tool.
  3. Pop rivets join sheet to sheet, such as flashing laps and gutter joints.
  4. Self Drilling Screw is the separate Jawdah accessory for fixing to support steel.
  5. Jawdah does not publish rivet sizes or materials; they are confirmed per project.

RFQ / BOQ checklist

  • Flashing and gutter lap lengths
  • Planned rivet spacing
  • Sheet thicknesses at the joints
  • Flashing and panel facing material
  • Head colour for visible trims
  • Sealed or open-core rivet preference

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • Joining thin metal parts to each other, such as flashing laps, cappings, trims and gutter joints, where only one side can be reached.

  • Yes. Pop Rivets are listed in the Jawdah sandwich panel accessories range. Size and material are confirmed for each project.

  • Yes. Pop rivet is the common name for a blind rivet, which is installed and set from one side of the joint.

  • No. Panels and flashings are fixed to the support steel with screws such as the self drilling screw. Rivets join sheet to sheet.

  • Yes, on weather-exposed laps. The rivet clamps the joint, and the sealant in the lap stops water passing between the sheets.

  • One compatible with the flashing and panel facing, to avoid galvanic corrosion. State the facing material so Jawdah can confirm the rivet.

Next step

Add rivets for your flashing laps

Send the flashing schedule, lap lengths and facing material. The Jawdah team will confirm the pop rivets and include them in your quotation.