Jawdah Industrial Co. Ltd.

Sandwich Panel Accessories · Fasteners

Self Drilling Screw for Sandwich Panel Accessories

The Self Drilling Screw is the fastener in the Jawdah sandwich panel accessories range that drills its own hole and fixes roof and wall panels through to the supporting steel in one step.

Range
Sandwich panel accessories
Size and material
Confirmed per project
Self drilling screw with hex washer head and EPDM sealing washer, for fixing sandwich panels and flashings

Overview

Quick answer

A self drilling screw for sandwich panels has a drill point that cuts through the panel facing and the purlin or rail, then forms its own thread, so no pilot hole is needed. It is usually fitted with a sealing washer. Jawdah supplies it as a sandwich panel accessory; sizes and materials are not published and are confirmed for each project from panel thickness and steel.

Overview

What the self drilling screw does on a panel envelope

It is the item that carries panels on the structure, so its length, washer and coating are chosen for each project. Jawdah lists it in its accessories range and confirms the size, material and quantity from your panel thickness and support steel.

Every roof and wall panel has to be held on its purlins or rails against wind suction, thermal movement and its own weight. On sandwich panel buildings that job is normally done by self drilling screws driven from the outside face. The screw passes through the outer steel sheet, the PIR insulation core and the inner sheet, then drills into the support steel and locks into it.

Because the screw also pierces the weather face, it has a second job: the hole it makes has to stay sealed. That is why panel screws are normally fitted with a bonded sealing washer and why their placement, on a rib crown or in a flat area, follows the panel profile. A wrong screw rarely fails on the first day; it shows up later as a leak, a loose panel or a rust streak.

How it works

How a self drilling screw works

The tip is shaped like a small drill bit. As the screw turns, the tip cuts a hole through the metal, the flutes carry the swarf out, and the thread behind it then forms its own mating thread in the steel. Drilling and fixing happen in one pass with a screw gun, which saves a separate drilling step and keeps the hole tight around the shank.

The drill point has to be long enough to finish cutting through the support steel before the thread engages; otherwise the thread jams in a half-drilled hole. That is the main reason point type is matched to the thickness of the purlins or rails, while overall length is matched to the panel.

Types

Self drilling screw or another fixing?

The accessories range holds several ways of joining metal. The table shows where the self drilling screw fits; it is general guidance, not Jawdah item data.

Fixing choices in the sandwich panel accessories range (general guidance)
ItemTypical jobFixes into structure?
Self Drilling ScrewFix panels and flashings to purlins and railsYes
Pop RivetsJoin flashing laps and thin sheet to sheetNo
Silicon or Strip SealantSeal laps and joints; no structural holdNo

Applications

Matching screw length to Jawdah panel thickness

Length follows the panel depth at the fixing point plus the steel it fixes into. Jawdah Wall Sandwich Panels are published at 50, 75 and 100 mm, and Roof Sandwich Panels at 30/60, 50/80, 75/105 and 100/130 mm, where the larger figure is the depth at the rib. A screw through a roof rib therefore needs more length than one through a flat wall panel of similar core.

Coating and washer follow exposure. Roofs in Saudi Arabia run hot and see strong UV, and coastal sites add salt. Where panel facings are aluminium or stainless steel, use a screw material compatible with that facing to avoid galvanic corrosion.

Installation

Fixing practice on site

Drive the screw square to the panel face with a screw gun fitted with a depth setter. Stop when the sealing washer is seated and slightly compressed: an over-driven washer splits and an under-driven one leaks. Remove drilling swarf from the panel surface the same day, because steel filings rust and stain the coating.

Fix through the rib crown or the flat area as the panel profile requires, keep screws in line with the purlin below, and do not reuse a stripped hole. The Jawdah Installation Manual, available in hard copy, sets out the panel-side fixing requirements.

Selection pitfalls

Common mistakes with panel screws

These are the errors most often found on inspection of panel roofs and walls.

  • One screw length ordered for several panel thicknesses
  • Drill point too short for the purlin or rail steel
  • Washers crushed by an unset screw gun
  • Plain coating used on a coastal or humid site
  • Swarf left on the roof to rust

Choosing

What to send Jawdah to size the screws

Send the panel types and thicknesses, the purlin and rail section and steel thickness, the site location and the panel facing material. The Jawdah team then confirms the screw size, washer and quantity and adds them to the panel quotation with the other accessories, such as Pop Rivets for flashing laps.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Specifications recorded for this item

Jawdah lists the Self Drilling Screw by name in its sandwich panel accessories range. No size, material, coating or washer data is published for it, so the table states what is confirmed per project.

Self Drilling Screw: published data
PropertyJawdah data
ItemSelf Drilling Screw (accessory of the sandwich panel range)
Diameter and lengthNot published; confirmed per project
Material and coatingNot published; confirmed per project
Sealing washerNot published; confirmed per project
Drill point for support steelNot published; confirmed per project

Key facts

  1. The Self Drilling Screw is listed in the Jawdah sandwich panel accessories range.
  2. A self drilling screw drills its own hole and forms its own thread in one pass.
  3. Panel screw length depends on panel depth at the fixing point plus the support steel.
  4. Jawdah wall panels are published at 50, 75 and 100 mm; roof panels at 30/60, 50/80, 75/105 and 100/130 mm.
  5. Jawdah does not publish sizes or materials for this screw; they are confirmed per project.

RFQ / BOQ checklist

  • Panel types and thicknesses to be fixed
  • Purlin and rail section and steel thickness
  • Panel facing material
  • Site location and exposure (inland or coastal)
  • Fixing position: rib crown or flat area
  • Panel areas or screw quantities

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • It fixes roof and wall panels, and often flashings, to the steel purlins and rails. It drills its own hole and forms its own thread, so no pilot hole is needed.

  • Yes. The Self Drilling Screw is listed in the Jawdah sandwich panel accessories range. Size, material and quantity are confirmed for each project.

  • Long enough to pass through the full panel depth and engage the support steel fully. Jawdah does not publish a length table, so the length is confirmed from the panel thickness and steel section you send.

  • The bonded sealing washer closes the hole the screw makes in the weather face. It has to be seated correctly and resist heat and UV, or it becomes a leak point.

  • Not quite. A self tapping screw forms a thread in a hole that already exists; a self drilling screw has a drill point that makes the hole first, in the same pass.

  • Use a screw material compatible with the facing to avoid galvanic corrosion. State the facing material in your request so the Jawdah team can confirm the item.

Next step

Size your panel screws with the panel order

Send the panel thicknesses, support steel and site location. The Jawdah team will confirm the self drilling screw and add it to your quotation.