Jawdah Industrial Co. Ltd.

Sandwich Panel Accessories · Sealing

Strip Sealant for Sandwich Panel Laps and Flashings

The Strip Sealant is the pre-formed sealing strip in the Jawdah sandwich panel accessories range, laid between overlapping panels and flashings so the lap is closed against water, dust and air before it is fixed.

Role
Seals panel and flashing laps
Ordered by
Total lap length
Material and size
Confirmed per project
Strip Sealant, sandwich panel installation accessory

Overview

Quick answer

Strip sealant is a sealing material supplied as a ready-shaped tape or bead, placed inside a lap between two metal sheets and then compressed by the fasteners. On sandwich panel roofs and walls it seals end laps, side laps and flashing laps. Jawdah supplies it as a panel accessory; its material, width and roll length are not published and are confirmed per project.

Overview

What strip sealant does in a panel lap

Laps are where panel roofs most often leak, because two sheets meet and wind can drive rain uphill between them. A continuous strip placed in the lap before fixing closes that path. Jawdah lists the Strip Sealant as an accessory and confirms type and quantity per project.

Wherever one sheet overlaps another, a thin gap remains between them. Capillary action and wind pressure can carry water through that gap, and on a low-slope roof the water can travel a surprising distance uphill. Strip sealant fills the gap with a soft, continuous material that is squeezed between the sheets when the stitching screws or rivets are tightened.

Because the strip is laid before the next sheet goes on, its line is consistent along the whole lap, and it does not depend on reaching into a closed joint with a gun. That makes it the usual choice inside laps, while gun-applied Silicon suits exposed joints and finishing.

Applications

Where strip sealant is used

Typical positions on a sandwich panel building, as general guidance:

  • End laps between roof panels along the slope
  • Side laps where panel ribs overlap
  • Laps between flashings, such as ridge caps and gable trims
  • Under flashings where they bear on the panel face
  • Around gutter joints before riveting

Installation

Laying the strip correctly

Clean and dry the lap surfaces first; dust and moisture stop the strip from bonding. Lay the strip in one continuous run without stretching it, and join pieces by butting or overlapping the ends rather than leaving a gap. Position it on the weather side of the fastener line so the screws or rivets pass through or just behind it and compress it evenly. Place the next sheet on the same day so the strip is not left exposed to sun and sand.

Selection pitfalls

Common lap-sealing errors

These errors usually show up in the first rainy season.

  • Strip laid on dusty or wet metal
  • Gaps left where two strip pieces meet
  • Strip placed behind the fastener line instead of in front
  • Silicone used inside a closed lap instead of a strip
  • Laps left without any sealant to save time

Compatibility

Matching the strip to panels and flashings

The strip has to suit the lap it sits in: its width must cover the contact zone of Roof Sandwich Panels or of the flashing, and its material has to remain flexible under roof heat and stay compatible with the panel coating. Ask the Jawdah team to confirm the strip for your panel profile and site, together with the Self Drilling Screw and stitching fixings that compress it.

Choosing

Ordering strip sealant

Quantities follow lap length, not roof area. Measure the total length of end laps, side laps and flashing laps from the roof and wall drawings and send it with the panel profile. The Jawdah team confirms the strip type and roll count and adds it to the quotation with the other accessories.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Specifications recorded for this item

Jawdah lists the Strip Sealant by name in its sandwich panel accessories range. No material, width, thickness or roll length is published, so the table shows what is confirmed per project.

Strip Sealant: published data
PropertyJawdah data
ItemStrip Sealant (accessory of the sandwich panel range)
MaterialNot published; confirmed per project
Width, thickness and roll lengthNot published; confirmed per project
Service temperature and UV exposureNot published; confirmed per project

Comparison

Strip sealant, silicone or foam closure?

Three accessories in the range close gaps, but each in a different place. The comparison is general guidance.

Sealing accessories compared (general guidance)
ItemFormTypical position
Strip SealantPre-formed strip laid before fixingInside laps between sheets
SiliconGun-applied paste that curesExposed joints, edges and penetrations
Foam Closure TrimShaped foam fillerRib voids at eaves and ridges

Key facts

  1. The Strip Sealant is listed in the Jawdah sandwich panel accessories range.
  2. Strip sealant is laid inside laps between metal sheets before they are fixed.
  3. Strip sealant quantity follows total lap length.
  4. Silicon and Foam Closure Trim are separate Jawdah accessory items.
  5. Jawdah does not publish strip sealant material or dimensions; they are confirmed per project.

RFQ / BOQ checklist

  • Panel profile (roof or wall)
  • Total length of end laps and side laps
  • Total length of flashing laps
  • Site location and exposure
  • Panel coating or facing material
  • Other sealing items needed (silicone, closures)

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • A sealing material supplied as a pre-formed tape or bead that is laid inside a lap between two metal sheets and compressed by the fixings.

  • Yes. The Strip Sealant is listed in the Jawdah sandwich panel accessories range. Its type and quantity are confirmed for each project.

  • Use the strip inside laps that are closed once the next sheet is fixed. Silicone suits exposed joints, edges and penetrations that can be reached and tooled after fixing.

  • Measure the total length of all end laps, side laps and flashing laps. Jawdah confirms the roll count from that length and the panel profile.

  • On the weather side of the fastener line, so the screws or rivets compress it evenly and water meets the seal before it reaches the fixings.

  • No. Strip sealant seals the thin gap inside a lap; a foam closure fills the larger rib voids at the ends of panels under eaves and ridges.

Next step

Add lap sealing to your panel quotation

Send the panel profile and total lap lengths. The Jawdah team will confirm the strip sealant and include it with your panels.