Jawdah Industrial Co. Ltd.

Sandwich Panel Accessories · Closures

Foam Closure Trim for Sandwich Panel Rib Ends

The Foam Closure Trim is the shaped foam filler in the Jawdah sandwich panel accessories range that closes the open rib voids at the ends of profiled panels, under ridge caps, eave trims and wall flashings.

Role
Closes rib voids at panel ends
Profile and foam
Confirmed per project

Overview

Quick answer

A foam closure trim is a strip of foam cut to the exact rib profile of a panel. It is placed at the panel ends, under ridge caps, at eaves and at wall heads, so the flashing above bears on a closed surface instead of open ribs. Jawdah supplies foam closures as sandwich panel accessories; the profile, foam type and length are confirmed per project.

Overview

Why rib ends need a closure

A profiled panel ends in a row of open ribs. Left open, each rib is a path for wind-driven rain, sand, birds and insects into the building. A foam closure cut to the rib shape fills them. Jawdah lists it as an accessory and confirms the profile and quantity per project.

Roof panels have raised ribs for strength and drainage, and many wall panels are profiled too. Where the panel stops, at a ridge, an eave or the top of a wall, the flashing that covers the end is straight, but the panel underneath is not. The triangular or trapezoidal gaps left under the flashing are exactly the size that lets in driving rain, sand and nesting birds.

A foam closure trim is the profiled filler that closes those gaps. It sits between the panel and the flashing, follows the rib shape on one side and gives a flat bearing for the flashing on the other, and is usually sealed on both faces.

Applications

Where foam closures go

Typical positions on a sandwich panel building, as general guidance:

  • Under the external ridge cap at the top of roof panels
  • At the eave, above the gutter or eave trim
  • Where roof panels meet a parapet or higher wall
  • At the head of profiled wall panels under the flashing
  • At the base of profiled wall panels where specified

Compatibility

Matching the closure to the panel profile

A closure only works if it matches the rib shape of the panel it sits on. A closure cut for one profile will leave gaps on another, so state the exact panel, such as the Roof Sandwich Panels profile, when ordering. Top and bottom closures can differ, because the panel face looks different from above and below.

The closure works with the flashing over it, such as the RF-103 External Ridge Cap or the RF-106 Eave Trim, and with a sealant line so water cannot pass around it.

Installation

Fitting foam closures

Place the closure on clean, dry panel ends before the flashing is fixed, aligned so each lobe sits fully in its rib. Butt the pieces tightly end to end. Seal the closure to the panel and to the underside of the flashing as the detail requires, then fix the flashing so it compresses the foam slightly. Check from the outside that no daylight shows through the ribs before moving on.

Selection pitfalls

Closure mistakes found on inspections

These are the usual reasons birds and sand get under ridges and eaves.

  • Closures left out to save time
  • Closure profile not matching the panel rib
  • Gaps between closure pieces
  • No sealant between closure, panel and flashing
  • Silicone used to fill rib voids instead of a closure

Choosing

Ordering foam closures

Count closures by length: measure the ridge, eave and wall-head lengths where profiled panels end and send them with the panel profile. The Jawdah team confirms the closure and adds it to the quotation with the flashings and other accessories, such as Strip Sealant.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Specifications recorded for this item

Jawdah lists the Foam Closure Trim by name in its sandwich panel accessories range. No foam type, profile drawing or length is published, so the table shows what is confirmed per project.

Foam Closure Trim: published data
PropertyJawdah data
ItemFoam Closure Trim (accessory of the sandwich panel range)
ProfileMust match the panel rib; confirmed per project
Foam materialNot published; confirmed per project
Piece lengthNot published; confirmed per project

Comparison

This accessory and the RF-107 roof flashing item

The Jawdah product list includes a Foam Closure Trim twice: here, as an accessory, and as RF-107 Foam Closure Trim in the roof flashing range. The published data does not say whether they are the same part. When ordering, name the position and panel profile, and the Jawdah team will confirm which item applies.

Two foam closure entries in the Jawdah product list
EntryRangeUse on this page
Foam Closure TrimSandwich panel accessoriesRib-void closures in general
RF-107 Foam Closure TrimRoof flashingsRoof flashing item; see its own page

Key facts

  1. The Foam Closure Trim is listed in the Jawdah sandwich panel accessories range.
  2. Jawdah also lists RF-107 Foam Closure Trim in its roof flashing range.
  3. Foam closures fill rib voids at panel ends under ridges, eaves and wall heads.
  4. A foam closure must match the rib profile of the panel.
  5. Jawdah does not publish closure foam type or dimensions; they are confirmed per project.

RFQ / BOQ checklist

  • Panel profile at each closure position
  • Ridge length
  • Eave length
  • Wall-head and parapet lengths
  • Flashings used over the closures
  • Sealant needed with the closures

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • A strip of foam cut to the rib profile of a panel, used to close the open rib ends under ridge caps, at eaves and at wall heads.

  • Yes. The Foam Closure Trim is listed in the Jawdah sandwich panel accessories range, and an RF-107 Foam Closure Trim is listed with the roof flashings.

  • The ridge cap is flat but the panel below has ribs. Without a closure, wind-driven rain, sand, birds and insects can enter through each open rib.

  • No. The closure must match the rib profile of the panel it sits on, so state the exact panel profile when ordering.

  • The published data does not say. Name the position and panel profile when ordering and the Jawdah team will confirm the item.

  • By length along the ridges, eaves and wall heads where profiled panels end.

Next step

Close every rib end on your roof

Send the panel profile and ridge, eave and wall-head lengths. The Jawdah team will confirm the foam closure and include it in your quotation.