Jawdah Industrial Co. Ltd.

Roof Flashings · RF-107

RF-107 Foam Closure Trim for Sandwich Panel Roof Flashings

RF-107 Foam Closure Trim is the coded Jawdah roof flashing item that fills the open rib voids of a sandwich panel roof where the panels end under a flashing, at the ridge, the eave and the valley.

Code
RF-107
Shape
Follows the roof panel ribs
Data
Confirmed per project
RF-107 Foam Closure Trim, 3D render of the folded steel flashing profile for sandwich panel roofs

Overview

Quick answer

RF-107 Foam Closure Trim is a profiled foam strip shaped to the ribs of a sandwich panel roof. It is placed where the panels end under a flashing, at ridge caps, eave trims, eave gutters and valleys, to close the gaps between the ribs against wind, rain, dust, birds and insects. It must match the rib profile, so the panel variant is required. Jawdah confirms RF-107 per project.

Overview

Why a roof flashing set includes a closure

It is the part of the roof edge assembly that nobody sees once the caps are on, and the part that most often decides whether wind-driven rain and dust get in.

RF-107 is the last code in the Jawdah Roof Flashings range. Its profile follows the roof panel ribs; material grade, density and lengths are not published. This page explains RF-107 as part of the coded roof flashing set and how to order it with the caps and gutters it sits under.

A high-rib roof panel is not flat. Seen from its end, it is a series of raised ribs and lower troughs. When a flat flashing such as a ridge cap or an eave trim is laid across the panel ends, every rib leaves a gap underneath it. Along a long ridge those gaps add up to an open slot the full length of the building.

RF-107 Foam Closure Trim fills those gaps. It is cut to the same profile as the panel ribs, so it seats into the troughs and fills under the flat flashing. With sealant above and below, it turns the edge from a row of openings into a closed line.

Jawdah lists the closure twice, for two buying situations. RF-107 is the coded item inside Roof Flashings, ordered as part of the ridge, eave and valley details on this page. The same kind of product also appears in the Accessories range as Foam Closure Trim, for orders of loose accessories. Profile and supply are confirmed by Jawdah in either case.

How it works

Where RF-107 sits in each roof detail

As general guidance, closures are placed wherever a flashing crosses the panel ribs:

  • Under RF-103 External Ridge Cap, on both slopes
  • At the eave, under or behind RF-106 Eave Trim
  • Above RF-101 Eave Gutter, closing the panel ends over the gutter
  • Along both sides of RF-102 Valley Gutter
  • At wall abutments where a flashing crosses the ribs

Types

Rib-following versus flat roof flashings

RF-107 is the only Jawdah roof flashing whose shape follows the panel ribs. The others are formed to the edge they cover.

RF-107 compared with the flashings it supports (general guidance)
CodeShaped toRelation to RF-107
RF-107 Foam Closure TrimPanel rib profileCloses the rib voids
RF-103 External Ridge CapRidge angleSits on RF-107 at the apex
RF-106 Eave TrimEave edgeCloses the panel end with RF-107 behind
RF-101 / RF-102 guttersGutter sectionRF-107 closes the panel ends above

Applications

Matching RF-107 to the roof panel

A closure only works if its profile matches the ribs it fills. The 3-Rib Roof Panel and the 5-Rib Roof Panel have different rib patterns, so state the variant for each roof. Many closures are also handed: the one under a ridge cap fills the ribs from above, while the one at an eave may sit against the underside. Tell Jawdah each position so the right profile is supplied.

Selection pitfalls

Closure mistakes

A missing or wrong closure is invisible until the first storm.

  • Leaving closures out of the order because caps were ordered
  • Using a closure for the wrong rib variant
  • Fitting closures without sealant above and below
  • Stretching or cutting closures so they no longer meet end to end

Choosing

Ordering RF-107 with the roof flashings

List RF-107 against each flashing it serves: ridge lengths under RF-103, eave lengths at RF-106 or RF-101, and both sides of each RF-102 valley. Give the roof panel variant. Order it in the same Roof Flashings package; for a separate accessory order, use the Foam Closure Trim accessory page instead.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

RF-107 data status

No technical data sheet covers Jawdah flashings or closures. The values below are confirmed in the quotation.

RF-107 Foam Closure Trim data status
PropertyValue
Code and nameRF-107 Foam Closure Trim
RangeRoof Flashings
ProfileFollows the roof panel rib; confirmed per variant
Foam type and densityNot specified in the supplied data sheet
Supplied lengthsNot specified in the supplied data sheet

Key facts

  1. RF-107 Foam Closure Trim is a coded item in the Jawdah Roof Flashings range.
  2. RF-107 fills the rib voids of a sandwich panel roof under ridge caps, eave trims and gutters.
  3. The RF-107 profile must match the 3-rib or 5-rib roof panel variant.
  4. Jawdah also lists Foam Closure Trim in its Accessories range for loose accessory orders.
  5. Foam type, density and lengths of RF-107 are not published; Jawdah confirms them per project.

RFQ / BOQ checklist

  • Roof panel variant: 3-rib or 5-rib
  • Ridge lengths (both slopes) under RF-103
  • Eave lengths at RF-106 or RF-101
  • Valley lengths (both sides) at RF-102
  • Abutment lengths where flashings cross the ribs
  • Sealant to supply with the closures

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • The coded Jawdah roof flashing item that fills the rib voids of sandwich panel roof panels under ridge caps, eave trims and gutters.

  • They serve the same purpose. RF-107 is the code used inside the roof flashing package; the accessory listing is for ordering closures as loose accessories.

  • The closure fills the gaps between the ribs, so its profile must follow the actual rib pattern of the 3-rib or 5-rib panel.

  • Under the external ridge cap, at the eave with the eave trim or gutter, along valley gutters and wherever a flashing crosses the ribs.

  • The foam type, density and lengths are not published. Jawdah confirms them with the quotation.

  • Measure each ridge, eave and valley edge where a flashing crosses the ribs, noting both sides of ridges and valleys, and Jawdah confirms the quantity.

Next step

Close every rib under your flashings

Send the roof plan with ridge, eave and valley lengths and the panel variant. The Jawdah team will confirm RF-107 with the roof flashing package.