Jawdah Industrial Co. Ltd.

Roof Flashings · RF-106

RF-106 Eave Trim for Sandwich Panel Roofs

RF-106 Eave Trim is the coded Jawdah roof flashing that closes and finishes the low edge of a sandwich panel roof, covering the panel ends and guiding water off the edge cleanly, into a gutter or clear of the wall.

Code
RF-106
Position
Low roof edge (eave)
Works with
RF-101 gutter, RF-107 closures
Dimensions
Confirmed per project
RF-106 Eave Trim, 3D render of the folded steel flashing profile for sandwich panel roofs

Overview

Quick answer

RF-106 Eave Trim is a formed metal trim fitted along the eave of a sandwich panel roof. It covers the ends of the roof panels, carries water off the edge with a drip so it does not run back under the panels, and gives the roof edge a straight finish. It is used on free-draining eaves and alongside an eave gutter. Jawdah confirms the RF-106 profile per project.

Overview

What the eave trim finishes

Where RF-101 Eave Gutter collects the water, RF-106 deals with the edge itself: the cut panel ends, the core and the line the façade shows under the roof.

RF-106 is the sixth code in the Jawdah Roof Flashings range. Its girth, drip, gauge and material are not published; this page explains when an eave trim is used, how it relates to the gutter and fillers, and what Jawdah needs to confirm it.

At the eave, each roof panel ends with its two metal skins, its insulation core and the open ends of its ribs. Water arriving down the troughs leaves the roof at this line. If the edge is left raw, water curls back under the panel skin, the core edge is exposed to sun and moisture, and the roof line looks unfinished from the ground.

RF-106 Eave Trim covers that edge. It is fixed along the eave over or under the panel ends, closes the visible end of the panel, and is formed with a drip so water leaves the roof in a clean line. On a roof without gutters, it is the last surface water touches; on a roof with an RF-101 Eave Gutter, it guides water into the gutter and keeps the panel end tidy.

In the Jawdah product list, RF-106 is the single eave trim code; an earlier duplicate row of the same item has been merged into it. Jawdah confirms its section for each roof edge.

How it works

Eave trim, filler and gutter together

As general guidance, three items meet at the eave. The profile filler, such as RF-107 Foam Closure Trim, closes the rib voids so wind cannot drive rain up the troughs. The eave trim closes the panel end and forms the drip. Where a gutter is used, the gutter sits below the drip, its back lapped under the trim. The panel overhang is set so water clears the wall face or lands in the gutter.

Types

Eave trim or eave gutter?

Both codes sit on the same line, so the choice is about what happens to the water.

RF-106 and RF-101 at the eave (general guidance)
QuestionRF-106 Eave TrimRF-101 Eave Gutter
Main jobClose and finish the panel endsCollect and carry runoff
WaterDropped clear or into a gutterLed to outlets and down spouts
Used aloneYes, on free-draining eavesUsually with an edge trim or filler
Sized byPanel end and drip detailDraining roof area and outlets

Applications

Where RF-106 is used

Typical situations where an eave trim is used:

  • Free-draining eaves on small sheds, canopies and covered parking
  • Eaves with an RF-101 Eave Gutter, as the edge trim above it
  • Lean-to roofs where the low edge is visible from the yard
  • Roof edges over loading bays, where a clean drip line matters

Installation

Fitting order at the eave

Fit eave fillers and the eave trim before laying the roof panels where the detail places the trim under the panels; fit it after the panels where it caps their ends. Keep the trim straight along the full eave, lap lengths and seal laps, and fix through into the eave purlin or panel at the closer edge spacing the engineer sets.

Selection pitfalls

Eave edge mistakes

Eave problems are visible from the ground, which makes them expensive to ignore.

  • Raw panel ends left without a trim
  • No drip, so water runs back under the panel skin
  • Open rib voids above the trim
  • Overhang too short for water to clear the wall or reach the gutter
  • Ordering a gutter where a trim alone was enough, or the reverse

Choosing

Ordering RF-106

Mark every eave as RF-106 with its length, and say whether it drains freely or into an RF-101 gutter. Give the roof pitch, the panel variant, 3-Rib or 5-rib, and the colour. Send it with the Roof Flashings list and the roof panel RFQ.

Technical

Closer look

Approved photography of the product and its finish.
RF-106 Eave Trim, 3D render of the folded steel flashing profile for sandwich panel roofs

Specifications

RF-106 data status

No technical data sheet covers Jawdah flashings, so RF-106 values are confirmed in the quotation.

RF-106 Eave Trim data status
PropertyValue
Code and nameRF-106 Eave Trim
RangeRoof Flashings
Girth and dripNot specified in the supplied data sheet
Material and thicknessNot specified in the supplied data sheet
ColourConfirmed per project

Key facts

  1. RF-106 Eave Trim is a coded item in the Jawdah Roof Flashings range.
  2. RF-106 closes the low edge of a sandwich panel roof and forms a drip line.
  3. RF-106 is used on free-draining eaves and above an RF-101 Eave Gutter.
  4. Profile fillers such as RF-107 close the rib voids at the eave.
  5. Jawdah confirms RF-106 girth, material and colour per project.

RFQ / BOQ checklist

  • Roof plan with every eave marked RF-106 and its length
  • Free-draining eave or eave with RF-101 gutter
  • Roof pitch and panel overhang
  • Roof panel variant: 3-rib or 5-rib
  • Colour and material
  • Fillers and sealants to supply with the trim

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • A coded Jawdah roof flashing that closes and finishes the low edge of a sandwich panel roof and forms a drip so water leaves the edge cleanly.

  • Often yes. The gutter collects the water, while the eave trim closes the panel ends and guides water into the gutter. Jawdah confirms the detail per project.

  • Yes, as a general practice on free-draining eaves such as small sheds and canopies, where water drops clear of the wall.

  • RF-106 finishes the eave of the roof. WF-105 is a wall flashing that throws water clear at the base of a wall or over an opening.

  • No. Girth, drip, material and thickness are confirmed by Jawdah per project.

  • The Jawdah product list had the eave trim listed twice; the duplicate row was merged into RF-106.

Next step

Finish your eaves with RF-106

Send the roof plan with eave lengths and whether each eave has a gutter. The Jawdah team will confirm RF-106 and the eave items around it.