Jawdah Industrial Co. Ltd.

Roof Flashings · RF-104

RF-104 Internal Ridge Cap for Sandwich Panel Roofs

RF-104 Internal Ridge Cap is the coded Jawdah roof flashing that finishes the ridge of a sandwich panel roof from the inside, covering the joint between the two inner panel faces where the slopes meet.

Code
RF-104
Position
Ridge, room side
Partner
RF-103 External Ridge Cap
Dimensions
Confirmed per project
RF-104 Internal Ridge Cap, 3D render of the folded steel flashing profile for sandwich panel roofs

Overview

Quick answer

RF-104 Internal Ridge Cap is a formed metal trim fixed under the ridge of a sandwich panel roof, on the room side. It covers the gap between the inner faces of the two slopes, hides cut panel ends and the core, and closes the joint against dust and air movement. It is used with RF-103 External Ridge Cap where the panel underside is visible. Jawdah confirms its profile per project.

Overview

The ridge seen from inside

It is the room-side partner of the external ridge cap and matters wherever the underside of the roof panels is left exposed as the ceiling.

RF-104 is the fourth code in the Jawdah Roof Flashings range. Its girth, angle, gauge and material are not published. This page explains when an internal ridge cap is needed, what it closes and what Jawdah needs to confirm it.

A sandwich panel roof has two finished faces. In many warehouses, workshops, cold stores and sports halls there is no false ceiling, so the inner face of the roof panels is the ceiling. At the ridge, the inner faces of the two slopes meet with a gap and cut panel ends, and the insulation core is visible from below.

RF-104 Internal Ridge Cap closes that line from the inside. It is formed to the inside angle of the ridge and laps onto the inner face of both slopes, covering the panel ends and the joint. The weather is kept out by RF-103 External Ridge Cap above; RF-104 deals with what the room sees and what passes between the room and the ridge void.

This split matters for ordering: RF-103 is needed on every pitched panel roof, while RF-104 depends on whether the underside is exposed or sealed. Jawdah confirms the RF-104 section with the roof detail.

How it works

What the internal cap does

As general guidance, a room-side ridge trim serves four purposes:

  • Covers the cut ends and core of both panels at the apex
  • Closes the gap so dust and insects do not fall from the ridge void
  • Limits air movement between the room and the ridge, which matters in cooled spaces
  • Gives the exposed ceiling a straight, finished ridge line

Types

RF-104 next to the other ridge and edge codes

RF-104 is the only Jawdah roof flashing listed for the room side.

Room side versus weather side (general guidance)
CodeSideLine
RF-104 Internal Ridge CapRoom sideRidge
RF-103 External Ridge CapWeather sideRidge
RF-105 Gable TrimWeather sideSloping side edge
RF-106 Eave TrimWeather sideLow roof edge

Applications

Where RF-104 is used

RF-104 belongs in buildings where the roof underside stays visible or must be closed: warehouses and factories without a ceiling, cold rooms and controlled stores roofed with panels, food and clean areas where open joints overhead are not acceptable, and showrooms or halls with an exposed panel ceiling. Where a separate suspended ceiling hides the roof, the project may leave it out; that is a design decision to confirm with the consultant.

Selection pitfalls

Internal ridge mistakes

The internal ridge is often forgotten until the roof is closed.

  • Leaving RF-104 out of the order where the underside is visible
  • Matching the trim to the outside colour instead of the inner face
  • Fitting it after services have been run along the ridge
  • Open gaps at the ends where the ridge meets the gable

Choosing

Do you need RF-104?

If the roof panel underside is the finished ceiling, or the room is cooled or must stay clean, include RF-104 for every ridge, with the same length as RF-103. Note the inner facing and colour. Send both ridge codes together with the Roof Flashings list and the roof panel RFQ; for cold rooms, add the Cold Room Wall Panel layout.

Technical

Closer look

Approved photography of the product and its finish.
RF-104 Internal Ridge Cap, 3D render of the folded steel flashing profile for sandwich panel roofs
Internal ridge cap flashing profile (RF-104) for sandwich panel roofs

Materials

Matching the inner face

Jawdah roof panels are faced with PPGI, aluminium, stainless steel or galvanised iron, with polyester or PVDF coating; the standard colour is Cloud White (RAL 9002). The inner face of a roof panel is not always the same facing or colour as the outer face, so state the facing RF-104 must match. In hygienic or wash-down areas, ask Jawdah to confirm a trim material suited to that environment.

Specifications

RF-104 data status

No technical data sheet covers Jawdah flashings. The values below are confirmed in the quotation.

RF-104 Internal Ridge Cap data status
PropertyValue
Code and nameRF-104 Internal Ridge Cap
RangeRoof Flashings
Girth and lap onto each slopeNot specified in the supplied data sheet
AngleSet by the roof pitch; confirmed per project
Material, thickness and colourConfirmed per project

Key facts

  1. RF-104 Internal Ridge Cap is a coded item in the Jawdah Roof Flashings range.
  2. RF-104 finishes the ridge of a sandwich panel roof on the room side.
  3. RF-104 is used with RF-103 External Ridge Cap where the panel underside is exposed.
  4. RF-104 should match the inner panel facing, which can differ from the outer face.
  5. Jawdah confirms RF-104 profile, material and colour per project.

RFQ / BOQ checklist

  • Roof plan with ridges and whether each underside is exposed
  • Ridge lengths for RF-104 (normally equal to RF-103)
  • Roof pitch
  • Inner panel facing and colour
  • Room use: warehouse, cold room, food or clean area
  • Delivery with the roof panel package or separately

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • A coded Jawdah roof flashing that finishes the ridge of a sandwich panel roof on the room side, covering the joint between the inner panel faces.

  • No. It is needed where the panel underside is visible or the room must be closed, such as warehouses without ceilings and cold rooms.

  • No. RF-103 keeps the weather out on top; RF-104 finishes the inside. Where both are needed they are ordered together.

  • The colour and facing of the inner panel face, which may differ from the outside. State it separately in the RFQ.

  • An open ridge joint lets air move between the cooled room and the ridge void and leaves the core exposed overhead.

  • No. Girth, lap, angle, material and thickness are confirmed by Jawdah per project.

Next step

Finish the ridge inside and out

Send the roof plan, pitch and inner facing. The Jawdah team will confirm RF-104 and RF-103 together with the roof panels.