Jawdah Industrial Co. Ltd.

Sandwich Panel Accessories · Rainwater

Elbow for Sandwich Panel Rainwater Down Spouts

The Elbow is the bend fitting in the Jawdah sandwich panel accessories range that changes the direction of a rainwater down spout, at the gutter outlet, around an offset or at the discharge point.

Role
Changes down spout direction
Works with
Down spout and gutter outlet
Size and angle
Confirmed per project

Overview

Quick answer

An elbow is a short bent fitting that joins two lengths of down spout at an angle. On a sandwich panel building it is used at the top to return the pipe from the gutter outlet to the wall, at offsets around projections, and at the bottom to direct discharge away from the wall base. Jawdah supplies elbows as accessories; size, angle and material are confirmed per project.

Overview

Why a down spout needs elbows

Straight pipe alone rarely fits a building. Elbows bring the pipe from the projecting gutter outlet back to the wall and turn the water away at the base. Jawdah lists the Elbow as an accessory and confirms its size and angle with the down spout it serves.

A gutter outlet sits under the eave, out from the wall face, while the down spout must run down the wall where it can be bracketed. The gap between the two is closed with a pair of elbows, often called a swan neck or offset. A further elbow at the bottom, sometimes called a shoe or kick-out, turns the flow so water lands on a splash area or drain rather than against the base of the wall panels.

Without elbows, installers improvise with cut and bent pipe, which leaks at the bends and blocks with debris. That is why the Elbow is a separate accessory item alongside the Down Spout in the Jawdah range.

Types

Elbow compared with the down spout

The two items are ordered together but counted differently. This is general guidance.

Elbow and down spout in a rainwater run (general guidance)
ItemFunctionHow it is counted
Down SpoutCarries water straight down the wallBy length per pipe run
ElbowChanges direction at outlet, offsets and baseBy number per pipe run

Applications

Where elbows are fitted

Count elbows per down spout from the wall elevation and the eave section.

  • Top offset: from the gutter outlet back to the wall face
  • Mid offsets: around plinths, canopies or wall steps
  • Bottom outlet: turning discharge away from the wall base
  • Connections into a drain where the route changes direction

Compatibility

Matching the elbow to the down spout and gutter

An elbow has to be the same section and size as the down spout it joins, and its upper end has to fit the outlet of the gutter, such as the RF-101 Eave Gutter. Mixing a round elbow with a rectangular pipe, or two suppliers' sizes, leaves gaps that leak. Material and finish should also match the pipe so the run weathers evenly and dissimilar metals are not joined.

Ordering the elbows with the down spouts and gutters from Jawdah keeps the three parts on one schedule.

Installation

Fitting elbows so they do not leak

Assemble every joint so the upper piece sits inside the lower one in the direction of flow; water then runs past the joint instead of out of it. Seal joints as the pipe system requires and fasten them so they cannot pull apart under wind or thermal movement. Keep offsets short and to a moderate slope, because long horizontal runs collect sand and leaves. Leave the bottom elbow clear of the ground so it can be cleaned.

Selection pitfalls

Typical elbow errors

These show up at the first heavy rain.

  • Elbows not counted in the BOQ, so pipes are bent on site
  • Elbow size or shape different from the pipe
  • Joints lapped against the flow
  • No bottom elbow, so water hits the wall base

Choosing

How to order elbows

For each down spout, count the elbows from the eave section and wall elevation: usually a pair at the top, any offsets, and one at the bottom. Send these counts with the down spout lengths and gutter type; the Jawdah team confirms the elbow size and adds it to the quotation with the other accessories.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Specifications recorded for this item

Jawdah lists the Elbow by name in its sandwich panel accessories range. No angle, size or material is published, so the table shows what is confirmed per project.

Elbow: published data
PropertyJawdah data
ItemElbow (accessory of the sandwich panel range)
Bend angleNot published; confirmed per project
Size and sectionMatched to the down spout; confirmed per project
Material and finishNot published; confirmed per project

Key facts

  1. The Elbow is listed in the Jawdah sandwich panel accessories range.
  2. An elbow changes the direction of a rainwater down spout.
  3. Elbows are used at gutter outlets, offsets and the discharge point.
  4. The Down Spout is a separate Jawdah accessory item.
  5. Jawdah does not publish elbow sizes, angles or materials; they are confirmed per project.

RFQ / BOQ checklist

  • Number of down spouts
  • Elbows per down spout (top, offsets, bottom)
  • Down spout size and section if known
  • Gutter type at each outlet
  • Eave projection from the wall
  • Discharge detail at the base

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • It is a bent fitting that joins two pieces of down spout at an angle, so the pipe can change direction.

  • Yes. The Elbow is listed in the Jawdah sandwich panel accessories range. Its size, angle and material are confirmed with the down spout for each project.

  • Typically a pair at the top to bring the pipe from the gutter outlet to the wall, plus one at the bottom, plus any offsets. Count them from your wall elevation.

  • A swan neck is the offset made of two elbows that connects a projecting gutter outlet to a pipe running down the wall.

  • It turns the discharge away from the wall so water lands on a splash area or drain and does not soak the base of the wall panels.

  • The elbow must match the down spout section, size and material. Ordering both from Jawdah keeps them matched.

Next step

Order elbows with your down spouts

Send the number of down spouts and the elbows each needs. The Jawdah team will confirm the matching elbow and include it in your quotation.