Jawdah Industrial Co. Ltd.

Roof Flashings · RF-102

RF-102 Valley Gutter for Sandwich Panel Roofs

RF-102 Valley Gutter is the coded Jawdah roof flashing laid along the internal junction where two sandwich panel roof slopes meet, collecting water from both slopes and carrying it to outlets.

Code
RF-102
Position
Junction of two roof slopes
Water from
Two slopes
Dimensions
Confirmed per project
RF-102 Valley Gutter, 3D render of the folded steel flashing profile for sandwich panel roofs

Overview

Quick answer

RF-102 Valley Gutter is a formed metal gutter fitted in the valley between two sandwich panel roof slopes. Both slopes discharge into it, so it carries roughly double the water of an eave gutter serving one slope of the same size. It falls to outlets or to the eave and is sized per project. Jawdah confirms the RF-102 section from the roof plan.

Overview

Why the valley is the critical roof line

Multi-span warehouses, L-shaped plans and roofs that meet a higher block all create valleys, and each one concentrates rain from two directions into a single line.

RF-102 is the second code in the Jawdah Roof Flashings range. Its width, depth, girth, gauge and material are not published; this page explains the valley's role, how it differs from the eave gutter and what Jawdah needs to confirm RF-102.

A valley forms wherever two roof slopes fall toward each other: between the spans of a multi-span shed, at the inside angle of an L-shaped building, or where a lower roof meets a parallel higher one. The panel ends from both sides stop over the valley, and every trough on both slopes empties into it.

RF-102 Valley Gutter is the channel that takes that water. Unlike an eave gutter, which can overflow outward and be noticed, an overflowing valley gutter spills inward, over the panel ends and into the building. That makes the valley the roof line with the least room for error, and the one that most needs to be sized from the actual catchment.

Jawdah lists RF-102 next to RF-101 Eave Gutter in its Roof Flashings range. Both collect water; RF-102 does it between slopes and inside the roof plan.

RF-102 Valley Gutter

How it works

How a valley gutter is built into the roof

As general guidance, the valley gutter is laid on its own support before the adjoining panels, with its edges running up under the panel ends on each side. The panels overhang into the gutter so water drops in, and the rib voids at those ends are closed with profile fillers such as RF-107 Foam Closure Trim. The gutter falls along its length to outlets or to an open end at the eave, with lapped and sealed joints.

Types

Valley gutter compared with the eave gutter

The two Jawdah gutters look alike but face different demands.

RF-102 and RF-101 compared (general guidance)
AspectRF-102 Valley GutterRF-101 Eave Gutter
PositionInternal junction of two slopesLow outside edge of one slope
Water fromTwo slopesOne slope
If it overflowsWater enters the buildingWater spills outside
Access for cleaningOn the roofFrom the roof or the eave

Performance

What decides RF-102 size

The section of a valley gutter follows the combined area of the two slopes draining into it, their pitch, the outlet spacing and the rainfall design value set by the project engineer. Long valleys usually need intermediate outlets. Give Jawdah the roof plan with both slope dimensions per valley, outlet positions and the panel variant, 3-Rib or 5-Rib, so fillers follow the rib shape.

Maintenance

Inspecting valleys

Valleys collect what blows across the roof: sand, dust and debris settle in them faster than anywhere else. Walk and clear valleys and their outlets before the rains and after dust storms, check joint laps and sealant, and look for standing water that points to a blocked outlet or lost fall.

Applications

Valley gutter mistakes

Valley leaks are usually design or sequence errors.

  • Sizing the valley like an eave gutter, for one slope only
  • No intermediate outlets on long valleys
  • Panels fixed before the valley gutter is in place
  • Gutter edges stopping short of the panel ends
  • Open rib voids over the valley

Choosing

Ordering RF-102

Mark every valley on the roof plan as RF-102 with its length and the two slopes it serves. List outlet positions and the down spout route. RF-102 is quoted with the Roof Flashings package and the roof panels, together with the closures, sealants and Down Spout items it needs.

Technical

Closer look

Approved photography of the product and its finish.
RF-102 Valley Gutter, 3D render of the folded steel flashing profile for sandwich panel roofs
Valley gutter flashing profile (RF-102) for sandwich panel roofs

Specifications

RF-102 data status

No technical data sheet covers Jawdah flashings, so RF-102 values are confirmed in the quotation.

RF-102 Valley Gutter data status
PropertyValue
Code and nameRF-102 Valley Gutter
RangeRoof Flashings
Width, depth and girthNot specified in the supplied data sheet
Material and thicknessNot specified in the supplied data sheet
Support and outletsConfirmed per project

Key facts

  1. RF-102 Valley Gutter is a coded item in the Jawdah Roof Flashings range.
  2. RF-102 sits at the internal junction of two sandwich panel roof slopes and collects water from both.
  3. An overflowing valley gutter spills into the building, so valleys are sized for the combined catchment.
  4. RF-101 Eave Gutter collects water from one slope; RF-102 from two.
  5. Jawdah confirms RF-102 width, depth and material per project.

RFQ / BOQ checklist

  • Roof plan with every valley marked RF-102 and its length
  • Dimensions of both slopes draining into each valley
  • Roof pitch on each side
  • Outlet positions and down spout routes
  • Rainfall design value, if specified
  • Roof panel variant: 3-rib or 5-rib
  • Colour and material

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • A coded Jawdah roof flashing: the gutter laid where two sandwich panel roof slopes meet, collecting water from both.

  • It receives water from two slopes instead of one, and if it overflows the water goes into the building, so it is sized for the combined catchment.

  • Multi-span sheds, L-shaped or U-shaped plans, and any roof where two slopes fall toward each other.

  • As a general rule before the adjoining panels, so its edges sit under the panel ends on both sides.

  • No. Jawdah confirms width, depth, material, thickness and support for each valley.

  • The roof plan with valley lengths, the dimensions of both slopes, pitch, outlet positions and the panel variant.

Next step

Get your valley gutters sized

Send the roof plan with valley lengths, both slope sizes and outlet positions. The Jawdah team will confirm RF-102 and its accessories with the roof panels.