Jawdah Industrial Co. Ltd.

Wall Flashings · WF-101

WF-101 External Wall Flashing for Sandwich Panel Walls

WF-101 External Wall Flashing is the coded Jawdah wall flashing used on the outside of a sandwich panel wall, typically to close an external corner where two elevations meet.

Code
WF-101
Position
External wall corner
Counterpart
WF-102 Internal Wall Flashing
Dimensions
Confirmed per project
WF-101 External Wall Flashing, 3D render of the folded steel flashing profile for sandwich panel walls

Overview

Quick answer

WF-101 External Wall Flashing is a formed metal trim fitted on the outer face of a sandwich panel wall, usually at the external corner where two walls meet. It caps both panel edges, sheds rain past the corner joint and finishes the façade. Jawdah confirms its profile, material, colour and lengths per project against the wall drawings.

Overview

What WF-101 does on a panel wall

It covers both cut panel edges at that corner, protects the insulation core from sun, rain and dust, and gives the façade a straight, continuous corner line.

Jawdah lists WF-101 as the first item of its Wall Flashings range. Girth, gauge, material and length are not published yet, so this page explains the position and job of WF-101 and what to send so the Jawdah team can confirm the profile for your walls.

When two panel walls meet at an outside corner, each panel ends with a cut edge. The metal skins stop, the joint profile is interrupted and the insulation core is exposed. WF-101 External Wall Flashing is the trim that closes that edge from the outside. It wraps the corner, laps over the face of both panels and keeps weather away from the core and from the corner joint.

An external corner is also the most visible line on a panel building. It is seen from the street, it catches low sun and it shows every kink. A factory-formed corner trim keeps that line straight from base to eave, which site-bent sheet rarely achieves.

In Jawdah's coding, WF-101 is the external member of a pair: WF-102 Internal Wall Flashing handles the matching inside position. The exact section of WF-101 is confirmed by Jawdah against the project details; nothing on this page should be read as a published dimension.

How it works

How an external corner trim keeps water out

As general guidance, an outside corner trim has two legs at the corner angle. Each leg lies flat on one panel face and is fixed through into the panel or the framing behind it. Rain running across either face meets the leg and flows over it, not into the corner gap, because the trim sits on top of the panel skin.

Vertical lengths are lapped so that the upper length overlaps the lower one, the same shingle principle used across all wall flashings. Where the corner meets the base trim or the roof edge, the overlap again runs downhill so water is never led behind a joint.

Types

WF-101 among the Jawdah wall flashings

Jawdah codes five wall flashings. The table shows how WF-101 differs from its siblings by position. Choose WF-101 for outside corners; the other codes cover inside corners, steps between planes, free edges and drip edges.

Jawdah wall flashing codes by position (general guidance)
CodeItemTypical positionMain job
WF-101External Wall FlashingOutside corner of the wallCaps both panel edges from outside
WF-102Internal Wall FlashingInside cornerCloses the inside angle between walls
WF-103Z-AngleStep between two planesLaps one face over another
WF-104U-ChannelFree panel edge or baseReceives and covers a panel end
WF-105Drip TrimBase or head of an openingThrows water clear of the wall

Positions describe the usual use of each trim type; Jawdah confirms each profile per project.

Applications

Panels and edges WF-101 serves

WF-101 belongs on any Jawdah wall panel that turns an outside corner: the through-fixed Semi-Corrugated Wall Panel, the concealed-fix Secret-Fix Wall Panel and its grooved version, and the external corners of cold room and fire rated wall enclosures.

Jawdah wall panels are faced with PPGI, aluminium, stainless steel or galvanised iron, with polyester or PVDF coating, in standard Cloud White (RAL 9002) or other colours on request. A corner trim is normally ordered to match the panel face it covers, so state that match in the RFQ and let Jawdah confirm the flashing material.

Installation

Fitting WF-101 on site

Fit the corner trim once both elevations of that corner are fixed and plumb. Start at the base, over the base trim, and work upward so every upper length laps the one below. Fix through each leg into solid backing at a regular spacing, keep fasteners in a straight line, and use the sealant or strip sealant the wall detail calls for behind the legs.

Check the corner against a string line before final fixing. A trim fixed to a corner that is out of plumb makes the error visible along the whole height of the building.

Selection pitfalls

Common errors with external corner trims

Most problems at outside corners come from detailing, not from the trim itself.

  • Ordering one corner size for walls with different panel joints
  • Lapping lower lengths over upper ones, which leads water behind the trim
  • Leaving the panel core exposed where the corner meets the base
  • Corner trims in a different colour from the wall panels
  • Fixing into the panel skin alone where the detail needs solid backing

Choosing

When WF-101 is the right code

Use WF-101 wherever a wall turns outward and the corner is seen from outside. If the angle faces into a room or a recess, it is a WF-102 position. If the trim must close a single free edge rather than a corner, look at WF-104 U-Channel. Mark every outside corner on the elevations as WF-101 with its height, and the Jawdah team will price it with the Wall Flashings package.

Technical

Closer look

Approved photography of the product and its finish.
WF-101 External Wall Flashing: external corner flashing profile for sandwich panel walls
WF-101 External Wall Flashing, 3D render of the folded steel flashing profile for sandwich panel walls

Specifications

WF-101 data: what is published and what is not

No technical data sheet covers the Jawdah flashings. The values below are therefore not published and are confirmed by Jawdah in the quotation.

WF-101 External Wall Flashing data status
PropertyValue
Code and nameWF-101 External Wall Flashing
RangeWall Flashings, Flashings & Accessories
Leg sizes and girthNot specified in the supplied data sheet
Sheet material and thicknessNot specified in the supplied data sheet
Coating and colourConfirmed per project, normally matched to the panels
Supplied lengthsNot specified in the supplied data sheet

Key facts

  1. WF-101 External Wall Flashing is a coded item in the Jawdah Wall Flashings range.
  2. WF-101 typically closes the external corner of a sandwich panel wall from the outside.
  3. WF-102 Internal Wall Flashing is the inside-corner counterpart of WF-101.
  4. Jawdah has not published WF-101 dimensions, gauge or material; they are confirmed per project.
  5. Corner trims are normally matched to the panel facing and colour, standard Cloud White.

RFQ / BOQ checklist

  • Elevations with every external corner marked WF-101
  • Height of each corner and total running length
  • Wall panel type and joint: through-fixed or concealed-fix
  • Panel thickness at each corner
  • Flashing colour and facing material to match the panels
  • Base and roof-edge details where the corner starts and stops
  • Delivery with the panel package or separately

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • On the outside of a sandwich panel wall, typically at each external corner where two elevations meet, covering both panel edges.

  • WF-101 is the external member and closes outside corners; WF-102 Internal Wall Flashing closes inside corners and angles that face into a room or recess.

  • No. Leg sizes, girth, sheet thickness and lengths are not in a published data sheet and are confirmed by the Jawdah team for each project.

  • Corner trims are normally matched to the panel face. Jawdah panels are standard Cloud White with other colours on request, so state the colour for WF-101 in the RFQ.

  • The trim must seat against the actual panel joint, so state whether the wall is through-fixed or concealed-fix and Jawdah will confirm a suitable WF-101 profile.

  • Count every external corner on the elevations and give the height of each one. The total running length per colour is what the quotation needs.

Next step

Get WF-101 priced with your wall panels

Send the elevations with the external corners marked and their heights. The Jawdah team will confirm the WF-101 profile, colour and quantity with the panel quotation.