Jawdah Industrial Co. Ltd.

Wall Flashings · WF-104

WF-104 U-Channel for Sandwich Panel Walls

WF-104 U-Channel is the coded Jawdah wall flashing with a U-shaped section that receives or caps the end of a sandwich panel, closing its cut edge and core along a base, a head or a free vertical edge.

Code
WF-104
Section
U-shaped
Closes
One panel end, both faces
Size
Follows panel thickness
WF-104 U-Channel, 3D render of the folded steel flashing profile for sandwich panel walls

Overview

Quick answer

WF-104 U-Channel is a U-shaped metal trim for sandwich panel walls. The panel end sits inside the channel, so both faces and the cut core are covered in one piece. As general guidance it is used as a base or head channel, at free edges beside openings and at the ends of partitions. Jawdah confirms the WF-104 size against the panel thickness for each project.

Overview

What a U-channel does that other trims do not

Unlike a corner trim, which spans two panels, a U-channel wraps one panel end on both faces at once.

WF-104 is the fourth code in the Jawdah Wall Flashings range. Its internal width, leg depth, gauge, material and length are not published, so this page explains where a U-channel is used and the panel data Jawdah needs to confirm a WF-104 that fits.

Every sandwich panel has two metal faces and an insulation core between them. Where a panel ends without meeting another panel, at the floor, under a ceiling, beside a door or at the end of a partition, both faces and the core are exposed together. A corner trim cannot close that; a channel can.

WF-104 U-Channel has a base and two legs. The panel end slides into it or the channel is fitted over the end, so the legs lie on both faces and the base covers the core. Fixed to the floor or structure first, the same channel can also locate the panel bottom and hold the wall line straight while the panels are erected.

Because the channel must fit the panel, the width of WF-104 follows the panel thickness. That makes it the most thickness-dependent of the Jawdah wall flashings, and the reason Jawdah confirms it per project rather than as one stock size.

Types

WF-104 against the other wall flashing codes

The test is whether the trim closes one panel end or a junction between two surfaces.

WF-104 compared with sibling codes (general guidance)
CodeClosesPanels involved
WF-104 U-ChannelOne panel end, both faces and coreOne
WF-101 External Wall FlashingOutside cornerTwo
WF-102 Internal Wall FlashingInside cornerTwo
WF-103 Z-AngleStep between planesPanel and element below
WF-105 Drip TrimBottom edge water linePanel and edge below

Applications

Typical WF-104 positions

As general guidance, U-channels on panel walls are used at:

  • The base of internal walls and cold room walls, fixed to the floor
  • The head of partition walls under a ceiling or roof
  • Free vertical edges beside doors and openings
  • Exposed ends of partitions that stop in a room
  • Panel ends at movement or construction breaks

Compatibility

Panel thickness decides the channel

Jawdah wall panels are offered in several thicknesses, for example the Cold Room Wall Panel and the Secret-Fix Wall Panel families. A WF-104 channel must suit the exact panel thickness at each position, so list thickness per wall in the RFQ. Where walls of different thickness meet, each gets its own channel size.

Installation

Installing a base or head channel

For base use, set out the wall line, fix the channel to the level floor and seal under it where the detail needs a seal, then stand the panels into it. For head use, fix the channel to the structure above in line with the base. For free edges, fit the channel over the panel end after the panel is plumb and fix through both legs as the detail shows.

Selection pitfalls

U-channel mistakes

Most U-channel problems are fit problems.

  • Ordering one channel width for panels of several thicknesses
  • Fixing a base channel to an uneven floor without levelling
  • Using a U-channel as an outside base trim where water must be thrown clear
  • Leaving the core open at partition ends to save one trim

Choosing

When to choose WF-104

Choose WF-104 wherever a single panel end needs closing on both faces. Where the edge is external and water must drop clear of the wall, a WF-105 Drip Trim or WF-103 Z-Angle is the usual choice instead. Mark every WF-104 position with its panel thickness and length and send it with the Wall Flashings list.

Technical

Closer look

Approved photography of the product and its finish.
WF-104 U-Channel at a wall panel overlap, 3D render of the folded steel flashing profile for sandwich panel walls

Specifications

WF-104 data status

No technical data sheet is available for Jawdah flashings, so the WF-104 values below are confirmed in the quotation.

WF-104 U-Channel data status
PropertyValue
Code and nameWF-104 U-Channel
RangeWall Flashings
Internal widthSet by panel thickness; confirmed per project
Leg depth, material and thicknessNot specified in the supplied data sheet
Supplied lengthsNot specified in the supplied data sheet

Key facts

  1. WF-104 U-Channel is a coded item in the Jawdah Wall Flashings range.
  2. A U-channel closes one sandwich panel end on both faces and covers the core.
  3. WF-104 width follows the panel thickness, so it is confirmed per project.
  4. Typical U-channel uses are floor and head channels and free panel edges.
  5. WF-104 is a wall flashing, separate from the U-channel of suspended ceiling systems.

RFQ / BOQ checklist

  • Plans with each WF-104 position: base, head or free edge
  • Panel thickness at every position
  • Running length per thickness
  • Floor and head conditions where channels are fixed
  • Colour and facing to match
  • Delivery with the panel package or separately

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • A coded Jawdah wall flashing with a U section that receives or caps a sandwich panel end, covering both faces and the core.

  • Typically as a floor or head channel for internal and cold room walls, and to close free panel edges beside openings and at partition ends.

  • The channel width follows the panel thickness. Give the thickness of each wall and Jawdah confirms the matching WF-104.

  • No. Suspended ceiling systems use their own U-channel component. WF-104 is a sandwich panel wall flashing.

  • Not as a rule. A channel holds the panel end but does not throw water clear; external bases usually need a drip detail such as WF-105.

  • No. Width, leg depth, thickness, material and lengths are confirmed by Jawdah per project.

Next step

Get WF-104 matched to your panel thickness

Send the wall layout with panel thicknesses and channel positions. The Jawdah team will confirm the WF-104 sizes and quantities with the panels.