Jawdah Industrial Co. Ltd.

Wall Flashings · WF-105

WF-105 Drip Trim for Sandwich Panel Walls

WF-105 Drip Trim is the coded Jawdah wall flashing with a projecting drip edge, fitted at the bottom of a sandwich panel wall or above an opening so rainwater leaves the wall in drops instead of running back behind the joint.

Code
WF-105
Job
Throws water clear of the wall
Position
External base, opening heads
Dimensions
Confirmed per project
WF-105 Drip Trim, 3D render of the folded steel flashing profile for sandwich panel walls

Overview

Quick answer

WF-105 Drip Trim is a metal flashing with a downward drip edge that projects beyond the face of a sandwich panel wall. Water running down the panels reaches the edge and falls clear, rather than curling under and into the base joint or the frame below. It is used at external wall bases and over openings. Jawdah confirms its profile per project.

Overview

Why a wall needs a drip edge

It protects the panel bottom edge and the slab or frame joint below it, the two places where wall leaks most often start.

WF-105 is the fifth code in the Jawdah Wall Flashings range. Its projection, girth, gauge and material are not published; this page explains how a drip edge works, where WF-105 belongs and what Jawdah needs to confirm it for your walls.

Water running down a smooth wall does not simply fall off at the bottom. Surface tension lets it cling to the underside of an edge and travel back toward the wall, straight into the joint between the panel and the slab, upstand or window frame. That is how a dry-looking façade leaks at its base.

A drip trim breaks that path. It projects outward past the panel face and ends in a downturned or angled edge, so the water film has nowhere to cling and drops off clear of the joint. The bottom edge of the panel, including its insulation core, stays covered behind the trim.

Jawdah codes this item WF-105 Drip Trim. On external walls it is the usual partner of the base detail, while WF-104 U-Channel is used where a panel end is held in a channel. Jawdah confirms the WF-105 profile against each project detail.

How it works

The drip principle

As general guidance, three features make a drip edge work: it projects beyond the face it protects, its lower edge turns down or out to form the drip, and it has a slight outward fall so water never runs back. The upper part of the trim sits behind or under the panel bottom, following the same upper-over-lower lap as all Wall Flashings.

Types

Drip trim versus Z-angle and U-channel

Three Jawdah wall flashings work along horizontal lines. Pick by the job the line needs.

Horizontal-line wall flashings compared (general guidance)
CodeMain jobTypical line
WF-105 Drip TrimThrow water clear of the faceExternal base, opening heads
WF-103 Z-AngleCarry water across a step between planesPlane changes, panel-to-cladding joints
WF-104 U-ChannelHold and close a single panel endInternal bases, heads, free edges

Applications

Where WF-105 is fitted

Typical drip trim positions on a panel building:

  • External wall base, above the slab edge or upstand
  • Head of windows, doors and louvres, over the frame
  • Bottom of a panel wall that stops above another cladding
  • Horizontal breaks in tall façades where a drip line is detailed

Compatibility

Walls that need WF-105

Any external Jawdah wall exposed to rain needs a drip line at its base: the Semi-Corrugated Wall Panel, the Secret-Fix Wall Panel and the grooved secret-fix version alike. On through-fixed profiled panels, the bottom ends of the profile are also closed so wind cannot drive rain up the troughs; state the panel profile so Jawdah can confirm the closure with the trim.

Selection pitfalls

Drip trim errors that cause base leaks

A drip trim that is present but wrongly set does little.

  • Trim set flush with the panel face, so no drip forms
  • Trim sloping back toward the wall
  • Trim fitted over the panel bottom instead of behind or under it
  • Opening heads left without a drip, so water runs onto the frame
  • Joints between lengths lapped against the direction of view and flow

Choosing

Specifying WF-105

Mark the base of every external elevation and the head of every opening as WF-105, with running lengths. Where the base also changes plane, compare with WF-103 Z-Angle; where the panel end sits in a floor channel inside the building, use WF-104 U-Channel.

Technical

Closer look

Approved photography of the product and its finish.
WF-105 Drip Trim, 3D render of the folded steel flashing profile for sandwich panel walls

Specifications

WF-105 data status

No technical data sheet covers Jawdah flashings. The WF-105 values below are confirmed in the quotation.

WF-105 Drip Trim data status
PropertyValue
Code and nameWF-105 Drip Trim
RangeWall Flashings
Projection and girthNot specified in the supplied data sheet
Material and thicknessNot specified in the supplied data sheet
ColourConfirmed per project

Key facts

  1. WF-105 Drip Trim is a coded item in the Jawdah Wall Flashings range.
  2. A drip trim projects past the wall face so rainwater falls clear of the base joint.
  3. WF-105 is typically fitted at external wall bases and over openings.
  4. Internal panel bases are usually closed with a channel such as WF-104 instead.
  5. Jawdah confirms WF-105 profile, material and colour per project.

RFQ / BOQ checklist

  • Elevations with base lines and opening heads marked WF-105
  • Running length for bases and for openings
  • What lies below the wall: slab edge, upstand or other cladding
  • Wall panel type and profile
  • Colour and facing to match
  • Delivery with the panel package or separately

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • It projects past the face of a sandwich panel wall with a drip edge, so rainwater drops clear instead of running back into the base or frame joint.

  • Mainly at the base of external walls and at the heads of windows, doors and louvres.

  • Sealant ages and cracks. A drip edge keeps water away from the joint by its shape, so the sealant becomes a second line of defence, not the only one.

  • Usually not, because internal walls are not exposed to rain. Internal panel bases are often closed with a channel such as WF-104.

  • Jawdah has not published the WF-105 projection, girth or thickness. They are confirmed per project.

  • Elevations with the base lines and opening heads marked, running lengths, the panel type and the colour.

Next step

Close your wall base with WF-105

Send the elevations with base and opening-head lengths. The Jawdah team will confirm the WF-105 drip trim profile and quantity with the panels.