Jawdah Industrial Co. Ltd.

5-Rib Roof Panels · 30 mm

5-Ribs Roof Sandwich Panels — 30 mm

The 30 mm 5-rib roof panel is the slimmest member of Jawdah's five-rib PIR roof range: a 30 mm PIR core under a closely ribbed outer sheet with five ribs per panel width.

Profile
High rib, 5 ribs
Core thickness
30 mm
R-value (core)
1.30 m²·K/W
U-value (core)
0.77 W/m²·K
5-Ribs Roof Sandwich Panels 30 mm

Overview

Quick answer

Jawdah's 30 mm 5-rib roof panel is a high-rib PIR sandwich panel with five ribs per width and a 30 mm core. Its data sheets give R 1.30 m²·K/W and U 0.77 W/m²·K for the core. The fine rib pattern and a semi-corrugated or plain soffit suit gas station canopies, heavy-duty umbrellas and shade roofs that need little insulation. Rib geometry and spans are confirmed per project.

Overview

A thin five-rib panel for roofs that are seen

Jawdah's data sheet gives its core an R-value of 1.30 m²·K/W.

Light, shallow and finely ribbed, it is the natural starting point for canopies and shade roofs that are seen from below. This page covers that use, compares 30 mm with the 50 mm 5-rib panel, and lists what to send Jawdah. The profile is explained on the 5-Rib Roof Sandwich Panels page.

This panel joins a 30 mm rigid polyisocyanurate core to a high-rib outer sheet with five ribs across its width and to an inner sheet that is semi-corrugated or plain. Because the ribs repeat closely, the flat bays between them are short, so the surface looks even and is less prone to visible waviness than a profile with wider bays.

At 30 mm the core gives an R-value of 1.30 m²·K/W, the lowest in the five-rib range. That suits structures whose main job is shade and rain cover rather than climate control: a forecourt canopy or a large umbrella where the underside is in full view of customers and the space below is open to the air. Here the inner face matters as much as the core, because it is the finished ceiling people look at.

Types

Five ribs or three at 30 mm

The 3-rib 30 mm panel has the same core values. For a canopy, the five-rib profile's shorter flat bays give a tidier underside and edge; three ribs make more sense on long, plain industrial runs. Fillers and flashings must follow whichever profile is ordered.

3-rib and 5-rib at 30 mm
Aspect3-rib, 30 mm5-rib, 30 mm
Core R-value (m²·K/W)1.301.30
Core U-value (W/m²·K)0.770.77
Rib patternBold, widely spacedFiner, closely spaced
TroughsWideNarrower
Geometry and spansConfirmed per projectConfirmed per project

Pattern and trough rows are general guidance on rib count, not Jawdah measurements.

Applications

Canopies and shade roofs suited to 30 mm

Gas stations and heavy-duty umbrellas are among the roof applications Jawdah lists, and a fine rib pattern is often preferred where a canopy is viewed close up. As general guidance, the 30 mm five-rib panel suits open structures like these:

  • Fuel station forecourt canopies
  • Heavy-duty umbrellas and shade structures
  • Covered walkways and drop-off canopies
  • Open parking and loading shades

Choosing

Ordering 30 mm 5-rib panels

Agree the appearance first: external colour, coating and the internal face that will form the soffit. Then send Jawdah the canopy drawings, slope, purlin or rafter spacing, wind exposure and edge details, and ask for five-rib span data at 30 mm and matching fillers, eave and gable trims.

The roof category page names this thickness 30/60 mm, while the data sheets use the 30 mm core for their values; confirm the overall depth at the ribs before detailing the canopy fascia.

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Jawdah data

Five-rib data recorded for the 30 mm core

Jawdah's five-rib data sheet lists a 30 mm row. The remaining points are the high-rib roof family facts on the parent pages.

  • Core thickness: 30 mm, 5-rib high-rib profile
  • Thermal row: R 1.30 m²·K/W, U 0.77 W/m²·K (core only)
  • Insulation core: PIR; DIN 4102 B2 stated for the core material
  • Internal face: semi-corrugated or plain
  • Facings: PPGI, aluminium, stainless steel or galvanised iron
  • Coating: polyester or PVDF; Cloud White standard
  • Roof category designation: 30/60 mm

Specifications

30 mm 5-rib values and what is still missing

The data sheets derive the R-value from the 30 mm core and the PIR conductivity λ = 0.023 W/m·K; U is the reciprocal. Surface resistances and thermal bridges are left out, so treat these as core values. Five-rib cover width, rib height, span and weight are not stated in the supplied data.

5-rib roof panel, 30 mm: Jawdah data-sheet values
PropertyValue
Core thickness30 mm
Insulation corePIR, λ = 0.023 W/m·K (calculation basis)
R-value (core only)1.30 m²·K/W
U-value (core only)0.77 W/m²·K
ProfileHigh rib, 5 ribs per panel width
Internal faceSemi-corrugated or plain
Cover width, rib height and spacingNot specified in the supplied data sheet
Span, load and panel weightNot specified in the supplied data sheet

Comparison

30 mm on the five-rib thickness ladder

Moving up the five-rib table raises the core R-value: 1.30 at 30 mm, 2.17 at the 50 mm panel, 3.26 at the 75 mm panel and 4.35 at 100 mm. If the canopy shelters an enclosed kiosk or shop, check a thicker panel for that area.

5-rib roof panel thicknesses (Jawdah data sheet)
Core thicknessR-value (m²·K/W)U-value (W/m²·K)
30 mm1.300.77
50 mm2.170.46
75 mm3.260.31
100 mm4.350.23

Thermal values refer to the insulation core only and exclude surface resistances and thermal bridging.

Key facts

  1. Jawdah lists a 30 mm core thickness of its 5-rib high-rib PIR roof sandwich panel.
  2. The 30 mm 5-rib panel has a core R-value of 1.30 m²·K/W and a U-value of 0.77 W/m²·K (Jawdah data sheet).
  3. The 30 mm five-rib panel suits gas station canopies, heavy-duty umbrellas and shade structures (general guidance).
  4. The internal face of Jawdah roof panels, semi-corrugated or plain, forms the visible soffit of a canopy.
  5. Five-rib geometry and spans at 30 mm are confirmed by Jawdah per project.

RFQ / BOQ checklist

  • Profile and thickness: 5-rib, 30 mm
  • Roof area, slope and purlin spacing
  • Wind exposure and maintenance traffic
  • External facing, coating and colour
  • Internal face: semi-corrugated or plain
  • Panel lengths and quantities
  • Matching ridge, eave and gable flashings and fillers
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • The five-rib data sheets give R 1.30 m²·K/W and U 0.77 W/m²·K for the 30 mm core, calculated from λ = 0.023 W/m·K and excluding surface resistances.

  • Gas stations are among Jawdah's listed roof applications, and the thin five-rib panel suits open canopies that need shade and rain cover more than insulation. Confirm spans for the canopy frame with Jawdah.

  • Jawdah roof panels have a semi-corrugated or plain internal face. On a canopy it is the visible underside, so choose it together with the colour during design.

  • Five ribs give shorter flat bays and a more even surface, which suits roofs and edges seen up close. The core values are the same as the 3-rib 30 mm panel.

  • For an open canopy it usually is, because the space below is not cooled. If part of the canopy covers an enclosed, air-conditioned area, check a thicker five-rib panel for that part.

  • No. Cover width, rib height and rib spacing of the five-rib profile, and its spans at 30 mm, are confirmed by Jawdah per project.

Next step

Request 30 mm 5-rib panels for a canopy

Share the canopy drawings, colour, soffit face and frame spacing. Jawdah will confirm five-rib spans, trims and a quotation for the 30 mm panel.