Sinks · 50x120
Double Bowl Stainless Steel Sink 50x120
The 50x120 is a double bowl stainless steel sink from Jawdah's 50 cm width range whose bowls are listed on the right or the left of the unit.
- Size
- 50x120
- Listed in sink table as
- 120X50 (50 cm width range)
- Hole size
- 1.5”
- SS thickness
- 0.5 mm
Overview
Quick answer
Double Bowl Stainless Steel Sink 50x120 is a two-bowl sink listed as 120X50 in Jawdah's sink table. Its rows give a right or left bowl position, a 1.5-inch hole and 0.5 mm stainless sheet. It belongs to the 50 cm width range, and the range material is deep-drawing stainless steel, grades 304 and 201.
Overview
About Double Bowl Stainless Steel Sink 50x120
Longer double sinks usually leave room for counter beside the bowls, and the 50x120 records exactly where they go: right or left. It is the only 50 cm double bowl size with that entry. Paired with a 1.5-inch hole and one thickness, 0.5 mm, its data gives a clear, fixed specification for kitchens planned around one side of the counter.
Fourth of five double bowl sizes in the 50 cm group, the 50x120 is recorded in the sink table as 120X50. Shorter models in that width carry the entry 'All' or centre; this one is listed as right or left.
The outlet hole is 1.5 inches and the stainless thickness is 0.5 mm. That single thickness also applies to the 50x90 and the 50x150, while the shorter 50x80 and 50x100 offer more options.
In the 60 cm group, the 60x120 has the same length and also lists right or left, but with a larger hole and grade-linked sheet. For this 50x120, the grade comes from range data, 304 or 201, and Jawdah confirms it with your quotation.
Choose the 50x120 when your layout puts the bowls at one end of a 50 cm counter. If you want them centred, the 50x150 or the 50x90 are listed with a centre position. On a 60 cm counter, compare the 60x120. Tell Jawdah which side the bowls should be on.
Applications
Where it is used
Typical locations; suitability is confirmed per project:
- Kitchens where the bowls sit at one end and the rest of the counter stays clear
- Galley kitchens in apartments and staff housing
- Office kitchens with a dish rack or drying area beside the bowls
- Villa service kitchens used for washing larger serving dishes
Installation
Installation notes
Installation instructions were not supplied with the product data. Coordinate the outlet, the floor or worktop build-up and the falls before ordering, and follow the documents provided with the order.
- Confirm the outlet or pipe size it must connect to
- Check the finished level against the floor or worktop
- Protect the finish during construction
Technical
Closer look
Detailed product imagery is being prepared.
In preparationSpecifications
Technical data
Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.
| Property | Value | Source |
|---|---|---|
| Size / model (product list) | 50x120 | Jawdah product list |
| Listed in sink table as | 120X50 (50 cm width range) | Jawdah product data |
| Hole size | 1.5” | Jawdah product data |
| SS thickness | 0.5 mm | Jawdah product data |
| Bowl position | Right / Left | Jawdah product data |
| Material (sink range) | Deep-drawing stainless steel 304 and 201 | Jawdah product data |

Key facts
- Double Bowl Stainless Steel Sink 50x120 is listed under Sanitary Ware & Drainage Solutions.
- Role: a stainless steel kitchen sink with two bowls.
- Recorded for this size: listed in sink table as: 120X50 (50 cm width range); hole size: 1.5”; ss thickness: 0.5 mm; bowl position: Right / Left.
- Range data: material (sink range): Deep-drawing stainless steel 304 and 201.
- Values not on this page are confirmed by Jawdah on request.
RFQ / BOQ checklist
- Product and size or model (50x120)
- Quantity
- Outlet or pipe size it connects to
- Finish required
- Location and use of the area
- Project location and delivery date
Resources
Further chapters in preparation
Technical resources
Technical documentation is being prepared for this product.
Projects using this product
Project references are being prepared.
Compatible systems
Information on compatible systems for this product is being prepared.
Our technical team can share the current information on request.Ask the technical team
FAQ
Frequently asked questions
The sink table records the bowl position for this model as right or left. State the side you need and Jawdah confirms it with the quotation.
0.5 mm, according to the sink table. Range data names grades 304 and 201; Jawdah tells you which applies to your unit in the quotation.
Yes. The 60x120 double bowl also lists right or left, with a larger hole and thickness tied to grade.

Next step
Request a quotation for Double Bowl Stainless Steel Sink 50x120
Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.

