Jawdah Industrial Co. Ltd.

Sinks · 50x150

Double Bowl Stainless Steel Sink 50x150

The 50x150 is the longest double bowl stainless steel sink in Jawdah's 50 cm width range, with its bowls listed in the centre position.

Size
50x150
Listed in sink table as
150X50 (50 cm width range)
Hole size
1.5”
SS thickness
0.5 mm

Overview

Quick answer

Double Bowl Stainless Steel Sink 50x150 is a long two-bowl unit, shown as 150X50 at the top of the 50 cm width range in Jawdah's sink table. Its rows list a centre bowl position, a 1.5-inch hole and 0.5 mm stainless sheet. Grades for the sink range are deep-drawing stainless steel 304 and 201.

Overview

About Double Bowl Stainless Steel Sink 50x150

With 150 of length on a 50 cm counter, the 50x150 is the double bowl choice for long runs in narrower kitchens. Nothing longer exists in that width. The sink table places its bowls in the centre position, leaving counter on both sides, and records a 1.5-inch hole with 0.5 mm sheet, the same rows as the shorter 50x90.

Jawdah's sink table shows this model as 150X50, the fifth and last double bowl entry in the 50 cm width group. Only the 60x150, in the wider group, matches its length among double bowl sinks.

Three verified rows apply: centre bowl position, 1.5-inch hole, 0.5 mm stainless thickness. Those match the 50x90 exactly, which makes the two sizes a short and long version of the same listed specification. The 50x120 between them differs, listing right or left.

Range data gives the material as deep-drawing stainless steel 304 and 201, without assigning a grade to this size. Ask Jawdah to confirm the grade, the cut-out and the waste connection with the quotation.

Choose the 50x150 for a centred double sink on a long 50 cm counter. For the same rows in a much shorter unit, see the 50x90. If you want the bowls at one end, the 50x120 lists right or left. On a 60 cm counter of the same length, compare the 60x150.

Types

Sizes and variants

Other listed sizes of this product: 50x80, 50x90, 50x100, 50x120, 60x100, 60x120 and 60x150.

Applications

Where it is used

Typical locations; suitability is confirmed per project:

  • Long kitchens in villas where the sink sits in the middle of a full counter run
  • Shared staff kitchens where several people use the counter at once
  • Mosque and community hall kitchens that wash serving dishes in bulk
  • Back-of-house areas in small cafes with a narrow counter depth

Installation

Installation notes

Installation instructions were not supplied with the product data. Coordinate the outlet, the floor or worktop build-up and the falls before ordering, and follow the documents provided with the order.

  • Confirm the outlet or pipe size it must connect to
  • Check the finished level against the floor or worktop
  • Protect the finish during construction

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

Double Bowl Stainless Steel Sink 50x150: recorded data
PropertyValueSource
Size / model (product list)50x150Jawdah product list
Listed in sink table as150X50 (50 cm width range)Jawdah product data
Hole size1.5”Jawdah product data
SS thickness0.5 mmJawdah product data
Bowl positionCentreJawdah product data
Material (sink range)Deep-drawing stainless steel 304 and 201Jawdah product data

Key facts

  1. Double Bowl Stainless Steel Sink 50x150 is listed under Sanitary Ware & Drainage Solutions.
  2. Role: a stainless steel kitchen sink with two bowls.
  3. Recorded for this size: listed in sink table as: 150X50 (50 cm width range); hole size: 1.5”; ss thickness: 0.5 mm; bowl position: Centre.
  4. Range data: material (sink range): Deep-drawing stainless steel 304 and 201.
  5. Values not on this page are confirmed by Jawdah on request.

RFQ / BOQ checklist

  • Product and size or model (50x150)
  • Quantity
  • Outlet or pipe size it connects to
  • Finish required
  • Location and use of the area
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • Yes. It is listed last in that width in Jawdah's sink table, as 150X50.

  • The 50x90. Both list a centre bowl position, a 1.5-inch hole and 0.5 mm sheet.

  • The sink range is made from deep-drawing stainless steel 304 and 201. Which grade applies to your 50x150 is confirmed by Jawdah with the quotation.

Next step

Request a quotation for Double Bowl Stainless Steel Sink 50x150

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.