Jawdah Industrial Co. Ltd.

Sinks · 60x120

Double Bowl Stainless Steel Sink 60x120

The 60x120 is the double bowl stainless steel sink in Jawdah's 60 cm width range whose bowls are listed on the right or the left.

Size
60x120
Listed in sink table as
120X60 (60 cm width range)
Hole size
3”
Bowl position
Right / Left

Overview

Quick answer

Double Bowl Stainless Steel Sink 60x120 is a two-bowl sink recorded as 120X60 in Jawdah's sink table. In the 60 cm width range it lists a right or left bowl position and a 3-inch hole, with thickness of 0.5 mm in grade 201 or 0.6 mm in grade 304, from the deep-drawing stainless steel used for the range.

Overview

About Double Bowl Stainless Steel Sink 60x120

Kitchens planned with the bowls at one end of a deep counter are the natural fit for the 60x120. Of the three 60 cm double bowl sizes, it is the one recorded as right or left, between the open entry of the 60x100 and the centre position of the 60x150. Its hole is 3 inches, and its sheet thickness follows the grade you order.

This model is listed in the sink table as 120X60, the middle size of the 60 cm double bowl group. Its position entry, right or left, sets it apart from both neighbours.

The other rows follow the 60 cm pattern: a 3-inch hole and stainless sheet of 0.5 mm for grade 201 or 0.6 mm for grade 304. That makes the choice of grade the same as the choice of thickness on this unit.

Its 50 cm counterpart, the 50x120 double bowl, also lists right or left but has a smaller hole and 0.5 mm sheet with no grade named. If the counter depth allows either, decide based on the waste outlet and the grade you want.

Choose the 60x120 when the bowls should sit at one end of a 60 cm counter. For a shorter unit with the open 'All' entry, see the 60x100; for a centred layout, see the 60x150. On a 50 cm counter, the 50x120 is the comparable size. State the bowl side and the grade when you contact Jawdah.

Types

Sizes and variants

Other listed sizes of this product: 50x80, 50x90, 50x100, 50x120, 50x150, 60x100 and 60x150.

Applications

Where it is used

Typical locations; suitability is confirmed per project:

  • Kitchens with the bowls near a window at one end of the counter
  • Villa kitchens with a 60 cm deep counter and a drying area beside the bowls
  • Staff kitchens in offices and hotels
  • Service kitchens for majlis and hospitality areas

Installation

Installation notes

Installation instructions were not supplied with the product data. Coordinate the outlet, the floor or worktop build-up and the falls before ordering, and follow the documents provided with the order.

  • Confirm the outlet or pipe size it must connect to
  • Check the finished level against the floor or worktop
  • Protect the finish during construction

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

Double Bowl Stainless Steel Sink 60x120: recorded data
PropertyValueSource
Size / model (product list)60x120Jawdah product list
Listed in sink table as120X60 (60 cm width range)Jawdah product data
Hole size3”Jawdah product data
SS thickness0.5 mm (grade 201) / 0.6 mm (grade 304)Jawdah product data
Bowl positionRight / LeftJawdah product data
Material (sink range)Deep-drawing stainless steel 304 and 201Jawdah product data

Key facts

  1. Double Bowl Stainless Steel Sink 60x120 is listed under Sanitary Ware & Drainage Solutions.
  2. Role: a stainless steel kitchen sink with two bowls.
  3. Recorded for this size: listed in sink table as: 120X60 (60 cm width range); hole size: 3”; ss thickness: 0.5 mm (grade 201) / 0.6 mm (grade 304); bowl position: Right / Left.
  4. Range data: material (sink range): Deep-drawing stainless steel 304 and 201.
  5. Values not on this page are confirmed by Jawdah on request.

RFQ / BOQ checklist

  • Product and size or model (60x120)
  • Quantity
  • Outlet or pipe size it connects to
  • Finish required
  • Location and use of the area
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • The sink table lists right or left for this model. State your side with the enquiry, and Jawdah confirms it with the quotation.

  • Yes. The sink table records 0.6 mm in grade 304 and 0.5 mm in grade 201 for this model.

  • Both list right or left. The 60x120 has a 3-inch hole and grade-linked thickness; the 50x120 has a smaller hole and 0.5 mm sheet.

Next step

Request a quotation for Double Bowl Stainless Steel Sink 60x120

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.