Jawdah Industrial Co. Ltd.

Sinks · 50x80

Single Bowl Stainless Steel Sink 50x80

The 50x80 single bowl stainless steel sink is the shortest size in Jawdah's list that offers the bowl on the right or the left.

Size
50x80
Listed in sink table as
80X50 (50 cm width range)
Hole size
1.5”
SS thickness
0.35 / 0.4 / 0.5 mm

Overview

Quick answer

Single Bowl Stainless Steel Sink 50x80 is a one-bowl kitchen sink from the 50 cm width range, recorded in Jawdah's sink table as 80X50. Its bowl position is listed as right or left, the hole size is 1.5 inches, and the stainless sheet is offered at 0.35, 0.4 or 0.5 mm. The sink range uses deep-drawing stainless steel 304 and 201.

Overview

About Single Bowl Stainless Steel Sink 50x80

Step up from the 50x50 and the single bowl moves off-centre: the 50x80 lists the bowl on the right or on the left. That makes it the shortest Jawdah single bowl sink where you choose the bowl side to suit the cooker, the window or the dishwasher. It stays in the 50 cm width range with a 1.5-inch hole.

Jawdah's sink table writes this model as 80X50, length first, inside the 50 cm width range; the product list shows the same item as 50x80. It sits between the square 50x50 and the 50x100 in that group.

The verified rows give it a right or left bowl position rather than a centred one, which is the main practical difference from the 50x50. The outlet hole is 1.5 inches. Three stainless thicknesses are recorded for this size, 0.35, 0.4 and 0.5 mm, matching the 50x100 and the 50x50.

Grade is stated only for the sink range as a whole: deep-drawing stainless steel 304 and 201. When you order, state the bowl side, the thickness and the grade so Jawdah can confirm the exact unit with the quotation.

Choose the 50x80 if you want an offset bowl in the shortest length available. If a centred bowl is fine and space is tighter, look at the 50x50. If you have more counter length, the 50x100 keeps the same listed thickness and bowl-side options. Confirm the bowl side and cut-out with Jawdah.

Types

Sizes and variants

Other listed sizes of this product: 50x50, 50x100, 50x120, 50x150, 60x60, 60x100, 60x120 and 60x150.

Applications

Where it is used

Typical locations; suitability is confirmed per project:

  • Apartment kitchens where the bowl should sit away from the hob
  • Office pantries with a short counter run
  • Kitchen refits replacing an existing short single bowl unit
  • Staff kitchens in shops and small workplaces

Installation

Installation notes

Installation instructions were not supplied with the product data. Coordinate the outlet, the floor or worktop build-up and the falls before ordering, and follow the documents provided with the order.

  • Confirm the outlet or pipe size it must connect to
  • Check the finished level against the floor or worktop
  • Protect the finish during construction

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

Single Bowl Stainless Steel Sink 50x80: recorded data
PropertyValueSource
Size / model (product list)50x80Jawdah product list
Listed in sink table as80X50 (50 cm width range)Jawdah product data
Hole size1.5”Jawdah product data
SS thickness0.35 / 0.4 / 0.5 mmJawdah product data
Bowl positionRight / LeftJawdah product data
Material (sink range)Deep-drawing stainless steel 304 and 201Jawdah product data

Key facts

  1. Single Bowl Stainless Steel Sink 50x80 is listed under Sanitary Ware & Drainage Solutions.
  2. Role: a stainless steel kitchen sink with one bowl.
  3. Recorded for this size: listed in sink table as: 80X50 (50 cm width range); hole size: 1.5”; ss thickness: 0.35 / 0.4 / 0.5 mm; bowl position: Right / Left.
  4. Range data: material (sink range): Deep-drawing stainless steel 304 and 201.
  5. Values not on this page are confirmed by Jawdah on request.

RFQ / BOQ checklist

  • Product and size or model (50x80)
  • Quantity
  • Outlet or pipe size it connects to
  • Finish required
  • Location and use of the area
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • The sink table writes the length first. 80X50 in the table and 50x80 in Jawdah's product list refer to the same single bowl model in the 50 cm width range.

  • The sink table lists the bowl position for this model as right or left. State the side you need with your enquiry so Jawdah confirms it with the quotation.

  • A 1.5-inch hole, as recorded in Jawdah's sink table for this model.

Next step

Request a quotation for Single Bowl Stainless Steel Sink 50x80

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.