Sinks · 60x100
Single Bowl Stainless Steel Sink 60x100
The 60x100 is the only single bowl stainless steel sink in Jawdah's 60 cm width range that lists the bowl on the right or the left.
- Size
- 60x100
- Listed in sink table as
- 100X60 (60 cm width range)
- Hole size
- 3”
- Bowl position
- Right / Left
Overview
Quick answer
Single Bowl Stainless Steel Sink 60x100 is a 100X60 one-bowl sink in Jawdah's 60 cm width range. Its sink table rows give a right or left bowl, a 3-inch hole and a thickness of 0.5 mm for grade 201 or 0.6 mm for grade 304. The range is made from deep-drawing stainless steel.
Overview
About Single Bowl Stainless Steel Sink 60x100
If you need the bowl to one side on a 60 cm counter, the 60x100 is the size to choose: it is the only single bowl model in that width with a right or left bowl position. The others in the group, 60x60, 60x120 and 60x150, all centre the bowl. It keeps the 3-inch hole and grade-linked thickness of the 60 cm range.
Recorded as 100X60 in Jawdah's sink table, this model is the second size in the 60 cm width range, after the square 60x60. Its length matches the 50x100, but it belongs to the wider group and carries that group's data.
Three rows set it apart. The bowl position is right or left. The hole size is 3 inches. The stainless thickness depends on the grade you order: 0.5 mm for grade 201, 0.6 mm for grade 304. By comparison, the 50x100 lists a smaller hole and thicknesses that are not linked to a grade.
Before ordering, decide which side of the unit the bowl should sit on and check the waste connection on site against the 3-inch hole. Jawdah confirms the side, grade and cut-out with your quotation.
Choose the 60x100 when the counter is 60 cm deep and you want the bowl offset. If you prefer a centred bowl in this width, the next size up, 60x120, is the alternative. If the counter is only 50 cm deep, the 50x100 offers an offset bowl in the narrower group. Confirm the bowl side and grade with Jawdah.
Applications
Where it is used
Typical locations; suitability is confirmed per project:
- Family kitchens with 60 cm counters where the bowl sits next to a dishwasher
- Office kitchens where a side bowl leaves one clear stretch of worktop
- Kitchen refits in villas that already use a 3-inch waste outlet
- Staff kitchens in hotels and clinics
Installation
Installation notes
Installation instructions were not supplied with the product data. Coordinate the outlet, the floor or worktop build-up and the falls before ordering, and follow the documents provided with the order.
- Confirm the outlet or pipe size it must connect to
- Check the finished level against the floor or worktop
- Protect the finish during construction
Technical
Closer look
Detailed product imagery is being prepared.
In preparationSpecifications
Technical data
Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.
| Property | Value | Source |
|---|---|---|
| Size / model (product list) | 60x100 | Jawdah product list |
| Listed in sink table as | 100X60 (60 cm width range) | Jawdah product data |
| Hole size | 3” | Jawdah product data |
| SS thickness | 0.5 mm (grade 201) / 0.6 mm (grade 304) | Jawdah product data |
| Bowl position | Right / Left | Jawdah product data |
| Material (sink range) | Deep-drawing stainless steel 304 and 201 | Jawdah product data |

Key facts
- Single Bowl Stainless Steel Sink 60x100 is listed under Sanitary Ware & Drainage Solutions.
- Role: a stainless steel kitchen sink with one bowl.
- Recorded for this size: listed in sink table as: 100X60 (60 cm width range); hole size: 3”; ss thickness: 0.5 mm (grade 201) / 0.6 mm (grade 304); bowl position: Right / Left.
- Range data: material (sink range): Deep-drawing stainless steel 304 and 201.
- Values not on this page are confirmed by Jawdah on request.
RFQ / BOQ checklist
- Product and size or model (60x100)
- Quantity
- Outlet or pipe size it connects to
- Finish required
- Location and use of the area
- Project location and delivery date
Resources
Further chapters in preparation
Technical resources
Technical documentation is being prepared for this product.
Projects using this product
Project references are being prepared.
Compatible systems
Information on compatible systems for this product is being prepared.
Our technical team can share the current information on request.Ask the technical team
FAQ
Frequently asked questions
Yes. In Jawdah's sink table the 60x100 lists a right or left bowl, while the 60x60, 60x120 and 60x150 list a centre bowl.
The sink table gives 0.5 mm for grade 201 and 0.6 mm for grade 304 on this model.
They share the same length, but their data differs: the 60x100 lists a 3-inch hole and grade-linked thickness, while the 50x100 has a smaller hole and three thickness options.

Next step
Request a quotation for Single Bowl Stainless Steel Sink 60x100
Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.


