Jawdah Industrial Co. Ltd.

Sinks · 60x120

Single Bowl Stainless Steel Sink 60x120

The 60x120 is a long single bowl stainless steel sink in Jawdah's 60 cm width range, with the bowl centred between two stretches of counter.

Size
60x120
Listed in sink table as
120X60 (60 cm width range)
Hole size
3”
Bowl position
Centre

Overview

Quick answer

Single Bowl Stainless Steel Sink 60x120 is a centred-bowl stainless sink listed as 120X60 in the 60 cm width range of Jawdah's sink table. It has a 3-inch hole, and its thickness follows the grade: 0.5 mm in 201 or 0.6 mm in 304. Only the 60x150 is longer in this width.

Overview

About Single Bowl Stainless Steel Sink 60x120

The 60x120 brings the bowl back to the centre after the offset 60x100, and adds length on both sides. It is the third of four sizes in Jawdah's 60 cm single bowl group. As with every model in that width, the hole is 3 inches and the sheet is 0.5 mm in grade 201 or 0.6 mm in grade 304.

Listed in the sink table as 120X60, this sink sits between the 60x100 and the 60x150. Its length equals the 50x120, which is in the narrower 50 cm group.

Its verified rows are a centre bowl position, a 3-inch hole, and a thickness linked to grade: 0.5 mm when made in grade 201, 0.6 mm in grade 304. The 60x100 differs on bowl position, listing right or left. The 60x150 shares all three rows and is longer.

Compared with the 50x120 at the same length, this model is wider and carries the larger outlet, while the 50x120 is recorded at 0.5 mm without a named grade. Choose between them by counter depth and the waste connection you plan to use.

Choose the 60x120 for a symmetrical sink on a 60 cm deep counter of moderate length. If the run is longer, the 60x150 keeps identical rows. If you want the bowl offset, the 60x100 is the option in this width. On a 50 cm counter, look at the 50x120. Confirm the grade and cut-out with Jawdah.

Types

Sizes and variants

Other listed sizes of this product: 50x50, 50x80, 50x100, 50x120, 50x150, 60x60, 60x100 and 60x150.

Applications

Where it is used

Typical locations; suitability is confirmed per project:

  • Kitchens in villas with 60 cm counters and space on both sides of the sink
  • Island units where the bowl should sit centrally
  • Shared kitchens in offices, majlis service areas and schools
  • Light commercial pantries using a 3-inch waste outlet

Installation

Installation notes

Installation instructions were not supplied with the product data. Coordinate the outlet, the floor or worktop build-up and the falls before ordering, and follow the documents provided with the order.

  • Confirm the outlet or pipe size it must connect to
  • Check the finished level against the floor or worktop
  • Protect the finish during construction

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

Single Bowl Stainless Steel Sink 60x120: recorded data
PropertyValueSource
Size / model (product list)60x120Jawdah product list
Listed in sink table as120X60 (60 cm width range)Jawdah product data
Hole size3”Jawdah product data
SS thickness0.5 mm (grade 201) / 0.6 mm (grade 304)Jawdah product data
Bowl positionCentreJawdah product data
Material (sink range)Deep-drawing stainless steel 304 and 201Jawdah product data

Key facts

  1. Single Bowl Stainless Steel Sink 60x120 is listed under Sanitary Ware & Drainage Solutions.
  2. Role: a stainless steel kitchen sink with one bowl.
  3. Recorded for this size: listed in sink table as: 120X60 (60 cm width range); hole size: 3”; ss thickness: 0.5 mm (grade 201) / 0.6 mm (grade 304); bowl position: Centre.
  4. Range data: material (sink range): Deep-drawing stainless steel 304 and 201.
  5. Values not on this page are confirmed by Jawdah on request.

RFQ / BOQ checklist

  • Product and size or model (60x120)
  • Quantity
  • Outlet or pipe size it connects to
  • Finish required
  • Location and use of the area
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • It is the third of four sizes, after 60x60 and 60x100 and before 60x150, and the sink table lists it as 120X60.

  • Only length. Both list a centre bowl, a 3-inch hole and 0.5 mm in grade 201 or 0.6 mm in grade 304.

  • Choose by counter depth and outlet. The 60x120 is in the 60 cm range with a 3-inch hole; the 50x120 is in the 50 cm range with a smaller hole and 0.5 mm sheet.

Next step

Request a quotation for Single Bowl Stainless Steel Sink 60x120

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.