Deep Flange Track · 66 (50/60)
Deep Flange Track 66 (50/60) – Partition Metal Profile
Deep Flange Track 66 (50/60) is the middle of the three datasheet-documented deep flange runners, with a 60x66x60 mm section.
- Size
- 66 (50/60)
- Section
- 60x66x60 mm (60 mm flange)
- Material
- Galvanised steel
- Length
- 3000 mm
Overview
Quick answer
Jawdah's 66 (50/60) Deep Flange Track is a hot-dip galvanised steel runner, fixed at floor and ceiling to hold partition studs. The datasheet lists its section as 60x66x60 mm in the 60 mm flange version, placing it between the documented 52 and 72 sizes. Steel thickness is 0.35 up to 0.9 mm, with other thicknesses on request.
Overview
About Deep Flange Track 66 (50/60) – Partition Metal Profile
The 66 (50/60) track sits in the middle of the three sizes the datasheet documents, between 52 and 72. Its section is given as 60x66x60 mm with a 60 mm flange. For a specifier comparing documented options, it is the step between the smallest and largest of that trio, and its raw-material fire and humidity references match the rest of the range.
In a stud partition, the 66 track runs along the floor and soffit and receives the studs between its flanges, which are deeper than on the standard Track. The datasheet shows the 60 mm flange version of this size at 60x66x60 mm. The name also carries '(50/60)', the two flange heights listed for the track; the 50 mm option for this size is confirmed by Jawdah.
The datasheet references for fire apply to the raw material, not to a finished wall: BS 476 Part 6 – 1989, and surface flame spread Class 1 under BS 476 Part 7 – 1997. Humidity is referenced to EN ISO 6270-2. The steel itself is hot-dip galvanised to ASTM A653M, formed in 0.35 up to 0.9 mm thickness (other thicknesses on request) and cut to a standard 3000 mm length.
Use 66 (50/60) when the design calls for this size; it has a stated section, unlike most of the range. If the drawings allow a different documented size, 52 is smaller at 60x52x60 mm and 72 is larger at 60x72x60 mm. Confirm the flange height and steel thickness with Jawdah before ordering.
Types
Sizes and variants
This page is the 66 (50/60) size.
Other deep flange track sizes: Deep Flange Track 42 (50/60), Deep Flange Track 52 (50/60), Deep Flange Track 72 (50/60), Deep Flange Track 75 (50/60) and Deep Flange Track 77 (50/60).
Other deep flange track sizes: Deep Flange Track 92 (50/60), Deep Flange Track 102 (50/60), Deep Flange Track 125 (50/60) and Deep Flange Track 152 (50/60).
Applications
Where it is used
The datasheet lists the profiles for the installation of gypsum plasterboard. The deep flange track is used in:
- Base and head track for interior drywall partitions detailed at 66
- Wall linings on metal frames where the 60x66x60 mm datasheet section suits the submittal
- Projects that need raw-material fire and humidity references for the track steel
Installation
Installation notes
The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:
- Store profiles flat and dry, away from site water
- Wear eye protection when cutting metal
- Use profiles and accessories from the same system
Technical
Closer look
Detailed product imagery is being prepared.
In preparationSpecifications
Technical data
Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.
| Property | Value | Source |
|---|---|---|
| Size (product list) | 66 (50/60) | Jawdah product list |
| Section (datasheet) | 60x66x60 mm (60 mm flange) | Datasheet |
| Steel thickness | 0.35 up to 0.9 mm; other thicknesses on request | Datasheet |
| Material | Hot-dip galvanised steel complying with ASTM A653M | Datasheet |
| Standard length | 3000 mm | Datasheet |
| Fire (raw material) | BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997 | Datasheet |
| Humidity (raw material) | According to EN ISO 6270-2 | Datasheet |

Key facts
- Deep Flange Track 66 (50/60) is listed under Jawdah Drywall Solutions, Partition Metal Profiles.
- Role: a track with deeper flanges, fixed to the floor and soffit to hold the studs.
- Datasheet section for this size: 60x66x60 mm (60 mm flange).
- Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
- Other sizes listed: 42 (50/60), 52 (50/60), 72 (50/60), 75 (50/60), 77 (50/60), 92 (50/60), 102 (50/60), 125 (50/60), 152 (50/60).
RFQ / BOQ checklist
- Profile and size (Deep Flange Track 66 (50/60))
- Steel thickness
- Length and quantity
- Board type and layers the system carries
- Accessories needed (clips, rods, anchors, screws)
- Project location and delivery date
Resources
Further chapters in preparation
Technical resources
Technical documentation is being prepared for this product.
Projects using this product
Project references are being prepared.
Compatible systems
Information on compatible systems for this product is being prepared.
Our technical team can share the current information on request.Ask the technical team
FAQ
Frequently asked questions
It is the middle of the three: 52 is given as 60x52x60 mm, 66 as 60x66x60 mm and 72 as 60x72x60 mm, all in the 60 mm flange version.
No. The datasheet's references, BS 476 Part 6 – 1989 and Class 1 surface flame spread under BS 476 Part 7 – 1997, apply to the raw material. Any requirement for the complete partition must be checked separately.
The datasheet gives 0.35 up to 0.9 mm steel, with other thicknesses on request. Confirm the thickness for your partition height and boarding with Jawdah.

Next step
Request a quotation for Deep Flange Track 66 (50/60)
Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.
