Deep Flange Track · 75 (50/60)
Deep Flange Track 75 (50/60) – Partition Metal Profile
Deep Flange Track 75 (50/60) is a listed size of Jawdah's galvanised steel deep flange runner, placed just above the 72 size.
- Size
- 75 (50/60)
- Material
- Galvanised steel
- Length
- 3000 mm
Overview
Quick answer
The 75 (50/60) Deep Flange Track is a galvanised steel runner fixed at floor and soffit to hold drywall partition studs. It is the first listed size above the three that the datasheet documents, so its section is not stated; Jawdah confirms it with the quotation. Range data gives 0.35 up to 0.9 mm steel and a 3000 mm standard length.
Overview
About Deep Flange Track 75 (50/60) – Partition Metal Profile
Numerically, 75 (50/60) is only a short step from 72, yet the two are documented very differently. The datasheet gives 72 a 60x72x60 mm section but lists nothing for 75. That makes the 75 track a size to specify by name and confirm with Jawdah, not one to size from its neighbour's dimensions.
The track does the same job as the rest of the range: fixed to the floor and soffit, it holds the ends of the studs between flanges deeper than those of the standard Track. Its name carries '(50/60)', the two flange heights listed for the track. Which flange height and section dimensions apply to 75 is confirmed by Jawdah, since the datasheet does not list this size.
Thickness is where the buyer has the most choice. The datasheet covers steel from 0.35 up to 0.9 mm and allows other thicknesses on request, so the gauge for a 75 track can be matched to the partition. The steel is hot-dip galvanised to ASTM A653M, standard length is 3000 mm, and the raw material's fire (BS 476 Part 6 – 1989; Class 1, BS 476 Part 7 – 1997) and humidity (EN ISO 6270-2) references apply.
Choose 75 (50/60) when it is the size on the drawings. If a datasheet section is required, 72 (50/60) at 60x72x60 mm is the nearest documented size below; there is no documented size above it. The 77 size is the next listed step up. For 75, confirm section, flange height and thickness with Jawdah at quotation.
Types
Sizes and variants
This page is the 75 (50/60) size.
Other deep flange track sizes: Deep Flange Track 42 (50/60), Deep Flange Track 52 (50/60), Deep Flange Track 66 (50/60), Deep Flange Track 72 (50/60) and Deep Flange Track 77 (50/60).
Other deep flange track sizes: Deep Flange Track 92 (50/60), Deep Flange Track 102 (50/60), Deep Flange Track 125 (50/60) and Deep Flange Track 152 (50/60).
Applications
Where it is used
The datasheet lists the profiles for the installation of gypsum plasterboard. The deep flange track is used in:
- Base and head runner for drywall partitions specified at 75
- Metal-framed wall linings where the design uses a 75 track
- Projects that compare 72 and 75 runners and need the 75 section confirmed in writing
Installation
Installation notes
The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:
- Store profiles flat and dry, away from site water
- Wear eye protection when cutting metal
- Use profiles and accessories from the same system
Technical
Closer look
Detailed product imagery is being prepared.
In preparationSpecifications
Technical data
Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.
| Property | Value | Source |
|---|---|---|
| Size (product list) | 75 (50/60) | Jawdah product list |
| Section (datasheet) | Not specified in the supplied datasheet | Datasheet |
| Steel thickness | 0.35 up to 0.9 mm; other thicknesses on request | Datasheet |
| Material | Hot-dip galvanised steel complying with ASTM A653M | Datasheet |
| Standard length | 3000 mm | Datasheet |
| Fire (raw material) | BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997 | Datasheet |
| Humidity (raw material) | According to EN ISO 6270-2 | Datasheet |

Key facts
- Deep Flange Track 75 (50/60) is listed under Jawdah Drywall Solutions, Partition Metal Profiles.
- Role: a track with deeper flanges, fixed to the floor and soffit to hold the studs.
- Section for this size: not specified in the supplied datasheet.
- Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
- Other sizes listed: 42 (50/60), 52 (50/60), 66 (50/60), 72 (50/60), 77 (50/60), 92 (50/60), 102 (50/60), 125 (50/60), 152 (50/60).
RFQ / BOQ checklist
- Profile and size (Deep Flange Track 75 (50/60))
- Steel thickness
- Length and quantity
- Board type and layers the system carries
- Accessories needed (clips, rods, anchors, screws)
- Project location and delivery date
Resources
Further chapters in preparation
Technical resources
Technical documentation is being prepared for this product.
Projects using this product
Project references are being prepared.
Compatible systems
Information on compatible systems for this product is being prepared.
Our technical team can share the current information on request.Ask the technical team
FAQ
Frequently asked questions
No. Only 52, 66 and 72 have datasheet sections. Jawdah confirms the section for 75 with the quotation.
They are separate listed sizes. The 72 has a datasheet section of 60x72x60 mm; the 75 does not, so its dimensions are confirmed by Jawdah rather than taken from the 72.
The datasheet gives 0.35 up to 0.9 mm for the range, with other thicknesses on request. Confirm the thickness for this size with Jawdah.

Next step
Request a quotation for Deep Flange Track 75 (50/60)
Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.
