Jawdah Industrial Co. Ltd.

Stud · 123

Stud 123 – Partition Metal Profile

Stud 123 is one of the two widest studs on Jawdah's product list, and its section is confirmed by Jawdah on request rather than taken from the datasheet.

Size
123
Material
Galvanised steel
Length
3000 mm

Overview

Quick answer

Stud 123 is a wide galvanised steel stud for gypsum board partitions, second-largest of the ten sizes Jawdah lists. The datasheet does not name a section for it; the widest stud section it gives is 35x100x34 mm. Range data covering the studs states hot-dip galvanised steel complying with ASTM A653M, 0.35 up to 0.9 mm thickness and a 3000 mm standard length.

Overview

About Stud 123 – Partition Metal Profile

Stud 123 is for walls that need more depth than any documented stud gives. It sits between Stud 100 and Stud 150 on Jawdah's list. Because the datasheet stops naming stud sections at 35x100x34 mm, the exact profile of the 123 size is something Jawdah confirms with the quotation. Material and length follow the shared range data.

Stud 123 is a vertical framing member for drywall partitions with a deep cavity. Jawdah's product list includes it as the ninth of ten sizes.

The datasheet's stud sections end at 35x100x34 mm, and the 35x92x34 mm entry is the only other wide one, so neither describes this size. Its section is confirmed by Jawdah with the quotation, and it should not be estimated from Stud 100 or Stud 150.

The range data that applies to all studs is hot-dip galvanised steel complying with ASTM A653M, thickness from 0.35 up to 0.9 mm with other thicknesses on request, and a standard length of 3000 mm. The datasheet also gives raw-material references to BS 476 Part 6 – 1989, Class 1 under BS 476 Part 7 – 1997 and EN ISO 6270-2.

Choose Stud 123 when the design requires a cavity deeper than Stud 100 provides. If a documented size is acceptable, Stud 100 is the widest stud with a named section. Jawdah's product list includes a Track 125 in the track range; confirm the stud section, the track and the thickness before ordering.

Types

Sizes and variants

This page is the 123 size.

Other stud sizes: Stud 40, Stud 50, Stud 64, Stud 70 and Stud 73.

Other stud sizes: Stud 75, Stud 90, Stud 100 and Stud 150.

Applications

Where it is used

The datasheet lists the profiles for the installation of gypsum plasterboard. The stud is used in:

  • Deep partitions where large pipes or ducts run inside the wall cavity.
  • Walls drawn with a 123 stud in commercial or institutional projects.
  • Service walls where designers typically prefer a wide frame, subject to the system design.

Installation

Installation notes

The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:

  • Store profiles flat and dry, away from site water
  • Wear eye protection when cutting metal
  • Use profiles and accessories from the same system

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

Stud 123 – Partition Metal Profile: recorded data
PropertyValueSource
Size (product list)123Jawdah product list
Section (datasheet)Not specified in the supplied datasheetDatasheet
Steel thickness0.35 up to 0.9 mm; other thicknesses on requestDatasheet
MaterialHot-dip galvanised steel complying with ASTM A653MDatasheet
Standard length3000 mmDatasheet
Fire (raw material)BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997Datasheet
Humidity (raw material)According to EN ISO 6270-2Datasheet

Key facts

  1. Stud 123 is listed under Jawdah Drywall Solutions, Partition Metal Profiles.
  2. Role: the vertical member of a drywall partition that carries the boards on both faces.
  3. Section for this size: not specified in the supplied datasheet.
  4. Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
  5. Other sizes listed: 40, 50, 64, 70, 73, 75, 90, 100, 150.

RFQ / BOQ checklist

  • Profile and size (Stud 123)
  • Steel thickness
  • Length and quantity
  • Board type and layers the system carries
  • Accessories needed (clips, rods, anchors, screws)
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • No section is named for 123. The datasheet's widest stud section is 35x100x34 mm, so the 123 section is confirmed with the quotation.

  • Both are listed but neither has its own datasheet section. Stud 123 is the narrower of the two; confirm the section of whichever you specify.

  • The range data gives hot-dip galvanised steel complying with ASTM A653M, in thicknesses of 0.35 up to 0.9 mm, with others on request.

Next step

Request a quotation for Stud 123

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.