Jawdah Industrial Co. Ltd.

Stud · 50

Stud 50 – Partition Metal Profile

Stud 50 is a galvanised steel partition stud documented in Jawdah's data sheet as a 35x50x34 mm section, one step up from the narrowest size.

Size
50
Section
35x50x34 mm
Material
Galvanised steel
Length
3000 mm

Overview

Quick answer

Stud 50 is the second-smallest of Jawdah's ten listed drywall studs. It is a vertical profile that carries gypsum boards, and the datasheet records it as 35x50x34 mm. It is formed from hot-dip galvanised steel complying with ASTM A653M. Range-level data gives a 3000 mm standard length and a thickness range of 0.35 up to 0.9 mm.

Overview

About Stud 50 – Partition Metal Profile

Stud 50 sits just above the entry point of Jawdah's stud list. It keeps a partition compact while giving ten millimetres more web than Stud 40, according to the two datasheet sections. Buyers comparing the light end of the range usually weigh these two against each other, then confirm thickness and track with the quotation.

This size is listed by Jawdah as 50 and appears in the datasheet as a 35x50x34 mm stud section. The outer figures are the same as on every other stud section in the datasheet; only the middle figure changes from size to size.

Next to Stud 40, the 50 size deepens the partition cavity a little while keeping the frame light. Stud 64 is the next listed step if the wall needs more space, and it also has a datasheet section.

As with the rest of the profile range, the steel is hot-dip galvanised and complies with ASTM A653M. The datasheet gives thicknesses from 0.35 up to 0.9 mm, other thicknesses on request, and a standard length of 3000 mm. For the raw material it cites BS 476 Part 6 – 1989 and a Class 1 surface spread of flame under BS 476 Part 7 – 1997.

Stud 50 suits designs that need slightly more depth than Stud 40 without moving to the mid-range sizes. Both have datasheet sections, so the comparison is straightforward. Jawdah's product list includes a Track 52 next to this stud; confirm that pairing and the steel thickness for your partition with the quotation.

Types

Sizes and variants

This page is the 50 size.

Other stud sizes: Stud 40, Stud 64, Stud 70, Stud 73 and Stud 75.

Other stud sizes: Stud 90, Stud 100, Stud 123 and Stud 150.

Applications

Where it is used

The datasheet lists the profiles for the installation of gypsum plasterboard. The stud is used in:

  • Light internal partitions where the wall must stay compact.
  • Wall linings that need a little more cavity depth than the narrowest stud allows.
  • Furring frames for service runs behind a gypsum board finish, as is typical practice.

Installation

Installation notes

The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:

  • Store profiles flat and dry, away from site water
  • Wear eye protection when cutting metal
  • Use profiles and accessories from the same system

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

Stud 50 – Partition Metal Profile: recorded data
PropertyValueSource
Size (product list)50Jawdah product list
Section (datasheet)35x50x34 mmDatasheet
Steel thickness0.35 up to 0.9 mm; other thicknesses on requestDatasheet
MaterialHot-dip galvanised steel complying with ASTM A653MDatasheet
Standard length3000 mmDatasheet
Fire (raw material)BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997Datasheet
Humidity (raw material)According to EN ISO 6270-2Datasheet

Key facts

  1. Stud 50 is listed under Jawdah Drywall Solutions, Partition Metal Profiles.
  2. Role: the vertical member of a drywall partition that carries the boards on both faces.
  3. Datasheet section for this size: 35x50x34 mm.
  4. Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
  5. Other sizes listed: 40, 64, 70, 73, 75, 90, 100, 123, 150.

RFQ / BOQ checklist

  • Profile and size (Stud 50)
  • Steel thickness
  • Length and quantity
  • Board type and layers the system carries
  • Accessories needed (clips, rods, anchors, screws)
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • Both share the same steel and length data. In the datasheet, Stud 50 is 35x50x34 mm and Stud 40 is 35x40x34 mm, so the 50 size has the wider middle dimension.

  • Yes. Jawdah's data sheet names a 35x50x34 mm stud section, which matches this size.

  • Jawdah's product list includes a Track 52. Confirm that it is the right partner for your stud, and the thickness, when you request the quotation.

Next step

Request a quotation for Stud 50

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.