Track · 52
Track 52 – Partition Metal Profile
Track 52 is a galvanised steel partition channel documented in Jawdah's datasheet as 24x52x24 mm, one width above the narrowest track.
- Size
- 52
- Section
- 24x52x24 mm
- Material
- Galvanised steel
- Length
- 3000 mm
Overview
Quick answer
Track 52 is the second-narrowest of Jawdah's ten track sizes. It is the horizontal channel fixed at floor and ceiling to receive the studs of a gypsum board wall. The datasheet lists its section as 24x52x24 mm. The steel is hot-dip galvanised and complies with ASTM A653M, and range data gives a 3000 mm standard length with thickness from 0.35 up to 0.9 mm.
Overview
About Track 52 – Partition Metal Profile
Track 52 is the channel to look at when the partition uses Stud 50, which Jawdah's product list places beside it. It is one step wider than Track 42 and has its own datasheet section, 24x52x24 mm. The page below explains where it fits in the light end of the track range and what still needs confirming at quotation.
This size appears in Jawdah's product list as 52 and in the datasheet as a 24x52x24 mm track section. It is formed from hot-dip galvanised steel complying with ASTM A653M.
Track 52 sits between Track 42 and Track 66, and all three have named sections. Only the middle dimension changes among them, so the choice follows the stud width rather than any difference in material or length. Pick the narrower or wider neighbour only if the stud on the drawings changes.
The shared range data gives a 3000 mm standard length, thicknesses of 0.35 up to 0.9 mm with others on request, and humidity testing of the raw material according to EN ISO 6270-2.
Use Track 52 with the stud width that Jawdah lists beside it, Stud 50. For a narrower frame, Track 42 is the alternative; for a wider one, Track 66. Confirm the stud pairing, the thickness and the quantity of track with the quotation.
Applications
Where it is used
The datasheet lists the profiles for the installation of gypsum plasterboard. The track is used in:
- Top and bottom runners for light internal partitions.
- Channels for wall linings slightly deeper than the narrowest option.
- Fixing lines for furring frames behind gypsum board finishes, as is common practice.
Installation
Installation notes
The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:
- Store profiles flat and dry, away from site water
- Wear eye protection when cutting metal
- Use profiles and accessories from the same system
Technical
Closer look
Detailed product imagery is being prepared.
In preparationSpecifications
Technical data
Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.
| Property | Value | Source |
|---|---|---|
| Size (product list) | 52 | Jawdah product list |
| Section (datasheet) | 24x52x24 mm | Datasheet |
| Steel thickness | 0.35 up to 0.9 mm; other thicknesses on request | Datasheet |
| Material | Hot-dip galvanised steel complying with ASTM A653M | Datasheet |
| Standard length | 3000 mm | Datasheet |
| Fire (raw material) | BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997 | Datasheet |
| Humidity (raw material) | According to EN ISO 6270-2 | Datasheet |

Key facts
- Track 52 is listed under Jawdah Drywall Solutions, Partition Metal Profiles.
- Role: the track fixed to the floor and soffit that holds the studs.
- Datasheet section for this size: 24x52x24 mm.
- Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
- Other sizes listed: 42, 66, 72, 75, 77, 92, 102, 125, 152.
RFQ / BOQ checklist
- Profile and size (Track 52)
- Steel thickness
- Length and quantity
- Board type and layers the system carries
- Accessories needed (clips, rods, anchors, screws)
- Project location and delivery date
Resources
Further chapters in preparation
Technical resources
Technical documentation is being prepared for this product.
Projects using this product
Project references are being prepared.
Compatible systems
Information on compatible systems for this product is being prepared.
Our technical team can share the current information on request.Ask the technical team
FAQ
Frequently asked questions
The datasheet lists Track 52 as a 24x52x24 mm section in hot-dip galvanised steel complying with ASTM A653M.
Both share the same steel and length data. Their datasheet sections are 24x52x24 mm and 24x42x24 mm, so Track 52 has the wider middle dimension.
Jawdah's product list includes Stud 50. Confirm the pairing and steel thickness when you request the quotation.

Next step
Request a quotation for Track 52
Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.
