Jawdah Industrial Co. Ltd.

Track · 75

Track 75 – Partition Metal Profile

Track 75 is a listed width in Jawdah's partition track range whose section is not named in the datasheet and is confirmed by Jawdah on request.

Size
75
Material
Galvanised steel
Length
3000 mm

Overview

Quick answer

Track 75 is a galvanised steel floor and ceiling channel on Jawdah's product list, between Track 72 and Track 77. The datasheet does not name a section for this width, so its dimensions are confirmed with the quotation. Range data covering all tracks states hot-dip galvanised steel complying with ASTM A653M, a 3000 mm standard length and thickness from 0.35 up to 0.9 mm.

Overview

About Track 75 – Partition Metal Profile

Track 75 falls between two documented widths, which makes it easy to assume its dimensions. That would be a mistake: Jawdah lists it, but the datasheet gives no section for it. In the product list it sits next to Stud 73, another size without its own section. The material and length data shared by every track is what this page can state.

This page covers the 75 width of Jawdah's Track, the channel that holds studs at floor and ceiling. It is on the product list, but the datasheet does not name a 75 track section. The section is therefore confirmed by Jawdah with the quotation, not taken from Track 72 or Track 77.

The data that applies comes from the track range as a whole: hot-dip galvanised steel complying with ASTM A653M, thickness from 0.35 up to 0.9 mm with other thicknesses on request, and a 3000 mm standard length. Raw-material references are BS 476 Part 6 – 1989, Class 1 surface spread of flame under BS 476 Part 7 – 1997, and EN ISO 6270-2.

Read these as range figures rather than values measured for this width.

Specify Track 75 when it matches the stud in your design, typically the Stud 73 listed beside it, and ask Jawdah to confirm the section. If a documented width will do, Track 72 and Track 77 both have datasheet sections. Confirm thickness and pairing in the quotation.

Types

Sizes and variants

This page is the 75 size.

Other track sizes: Track 42, Track 52, Track 66, Track 72 and Track 77.

Other track sizes: Track 92, Track 102, Track 125 and Track 152.

Applications

Where it is used

The datasheet lists the profiles for the installation of gypsum plasterboard. The track is used in:

  • Floor and ceiling channels for partitions framed with Stud 73.
  • Runner replacement or matching on existing partitions built to this width.
  • Interior wall framing where the project specification names a 75 track.

Installation

Installation notes

The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:

  • Store profiles flat and dry, away from site water
  • Wear eye protection when cutting metal
  • Use profiles and accessories from the same system

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

Track 75 – Partition Metal Profile: recorded data
PropertyValueSource
Size (product list)75Jawdah product list
Section (datasheet)Not specified in the supplied datasheetDatasheet
Steel thickness0.35 up to 0.9 mm; other thicknesses on requestDatasheet
MaterialHot-dip galvanised steel complying with ASTM A653MDatasheet
Standard length3000 mmDatasheet
Fire (raw material)BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997Datasheet
Humidity (raw material)According to EN ISO 6270-2Datasheet

Key facts

  1. Track 75 is listed under Jawdah Drywall Solutions, Partition Metal Profiles.
  2. Role: the track fixed to the floor and soffit that holds the studs.
  3. Section for this size: not specified in the supplied datasheet.
  4. Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
  5. Other sizes listed: 42, 52, 66, 72, 77, 92, 102, 125, 152.

RFQ / BOQ checklist

  • Profile and size (Track 75)
  • Steel thickness
  • Length and quantity
  • Board type and layers the system carries
  • Accessories needed (clips, rods, anchors, screws)
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • No. The datasheet names other track sections but not 75, so Jawdah confirms this section with the quotation.

  • Jawdah's product list includes Stud 73. Neither has a named datasheet section, so confirm both with Jawdah.

  • Range data: hot-dip galvanised steel complying with ASTM A653M, 0.35 up to 0.9 mm thickness with others on request, and a 3000 mm standard length.

Next step

Request a quotation for Track 75

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.