Track · 42
Track 42 – Partition Metal Profile
Track 42 is the narrowest floor and ceiling channel in Jawdah's partition range, recorded in the datasheet as a 24x42x24 mm section.
- Size
- 42
- Section
- 24x42x24 mm
- Material
- Galvanised steel
- Length
- 3000 mm
Overview
Quick answer
Track 42 is a hot-dip galvanised steel runner that holds the top and bottom of the studs in a slim gypsum board partition. It is the smallest of Jawdah's ten listed track sizes, and the datasheet gives its section as 24x42x24 mm. Range data adds steel complying with ASTM A653M, thickness from 0.35 up to 0.9 mm and a 3000 mm standard length.
Overview
About Track 42 – Partition Metal Profile
A slim partition starts with a slim channel, and Track 42 is the narrowest one Jawdah lists. It is fixed to the floor and the soffit to set out the wall line, and the studs stand inside it. Its 24x42x24 mm section is named in the datasheet, so the geometry is documented. In Jawdah's product list it sits next to Stud 40.
Track 42 is a U-shaped channel of hot-dip galvanised steel complying with ASTM A653M. The datasheet lists it as 24x42x24 mm; the middle figure matches the size name and the outer figures are common to every track section in the datasheet.
As the first size in the list, it pairs naturally with the narrowest stud. Jawdah's product list places Stud 40 next to it, and the two together frame the thinnest partitions in the system. Track 52 is the next width up if the stud changes.
Range-level data covers the rest: a 3000 mm standard length, steel thickness of 0.35 up to 0.9 mm with other thicknesses on request, and raw-material references to BS 476 Part 6 – 1989 and Class 1 surface spread of flame under BS 476 Part 7 – 1997.
Choose Track 42 when the partition uses the slimmest stud. If the studs are wider, move to Track 52 or Track 66, which also have datasheet sections. Confirm with Jawdah that the track suits your stud, and agree the steel thickness, in the quotation.
Applications
Where it is used
The datasheet lists the profiles for the installation of gypsum plasterboard. The track is used in:
- Floor and ceiling channels for slim interior partitions.
- Head and base runners for narrow wall linings in front of masonry.
- Small boxing frames around pipes or columns, a typical use for narrow track.
Installation
Installation notes
The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:
- Store profiles flat and dry, away from site water
- Wear eye protection when cutting metal
- Use profiles and accessories from the same system
Technical
Closer look
Detailed product imagery is being prepared.
In preparationSpecifications
Technical data
Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.
| Property | Value | Source |
|---|---|---|
| Size (product list) | 42 | Jawdah product list |
| Section (datasheet) | 24x42x24 mm | Datasheet |
| Steel thickness | 0.35 up to 0.9 mm; other thicknesses on request | Datasheet |
| Material | Hot-dip galvanised steel complying with ASTM A653M | Datasheet |
| Standard length | 3000 mm | Datasheet |
| Fire (raw material) | BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997 | Datasheet |
| Humidity (raw material) | According to EN ISO 6270-2 | Datasheet |

Key facts
- Track 42 is listed under Jawdah Drywall Solutions, Partition Metal Profiles.
- Role: the track fixed to the floor and soffit that holds the studs.
- Datasheet section for this size: 24x42x24 mm.
- Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
- Other sizes listed: 52, 66, 72, 75, 77, 92, 102, 125, 152.
RFQ / BOQ checklist
- Profile and size (Track 42)
- Steel thickness
- Length and quantity
- Board type and layers the system carries
- Accessories needed (clips, rods, anchors, screws)
- Project location and delivery date
Resources
Further chapters in preparation
Technical resources
Technical documentation is being prepared for this product.
Projects using this product
Project references are being prepared.
Compatible systems
Information on compatible systems for this product is being prepared.
Our technical team can share the current information on request.Ask the technical team
FAQ
Frequently asked questions
Jawdah's data sheet records Track 42 as 24x42x24 mm in hot-dip galvanised steel complying with ASTM A653M.
Jawdah's product list includes Stud 40, the narrowest stud. Confirm the pairing with the quotation.
Yes. The track list runs from 42 up to 152, and Track 52 is the next size.

Next step
Request a quotation for Track 42
Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.
