Jawdah Industrial Co. Ltd.

Stud · 40

Stud 40 – Partition Metal Profile

Stud 40 is the narrowest vertical metal stud in Jawdah's product list, shown in the datasheet as a 35x40x34 mm section.

Size
40
Section
35x40x34 mm
Material
Galvanised steel
Length
3000 mm

Overview

Quick answer

Stud 40 is a hot-dip galvanised steel stud for gypsum board partitions and linings, and the smallest of the ten stud sizes Jawdah lists. The datasheet gives its section as 35x40x34 mm. Range data for the profiles adds a 3000 mm standard length and steel from 0.35 up to 0.9 mm thick, with other thicknesses on request.

Overview

About Stud 40 – Partition Metal Profile

When a partition or wall lining has to stay as slim as possible, Stud 40 is the first size to look at in Jawdah's stud range. It is the narrowest of the ten listed sizes and one of those the datasheet covers by name, so its section is documented rather than assumed. The steel gauge for your job is agreed at quotation within the stated range.

Stud 40 is a vertical framing member for drywall, formed from hot-dip galvanised steel that the datasheet describes as complying with ASTM A653M. Its datasheet section reads 35x40x34 mm, and the middle figure matches the 40 in its name.

Because it sits at the bottom of the listed range, Stud 40 leaves the shallowest cavity of any Jawdah stud. Stud 50, the next size up, is the natural comparison when a little more depth is needed. Nothing else changes between them in the range data: both share the same steel and length figures.

The data that applies to the whole profile range includes a 3000 mm standard length, steel thickness from 0.35 up to 0.9 mm with other thicknesses on request, and humidity testing of the raw material according to EN ISO 6270-2. Confirm the thickness for your project when you ask for the quotation.

Choose Stud 40 when the drawing calls for the slimmest stud in the list. If the design needs more room for services or insulation, compare Stud 50 or Stud 64, which also have datasheet sections. For the floor and ceiling channel, Jawdah's product list includes a Track 42; confirm the matching track and the steel thickness with the quotation.

Types

Sizes and variants

This page is the 40 size.

Other stud sizes: Stud 50, Stud 64, Stud 70, Stud 73 and Stud 75.

Other stud sizes: Stud 90, Stud 100, Stud 123 and Stud 150.

Applications

Where it is used

The datasheet lists the profiles for the installation of gypsum plasterboard. The stud is used in:

  • Slim partitions in offices and apartments where floor space matters and the wall build-up is kept thin.
  • Wall linings fixed in front of existing masonry, a typical use for narrow studs.
  • Boxing around columns, pipes or ducts where only a shallow frame fits.

Installation

Installation notes

The supplied datasheet does not give spans, spacings or partition heights for this size. These are set by the system design and confirmed with Jawdah. General handling notes:

  • Store profiles flat and dry, away from site water
  • Wear eye protection when cutting metal
  • Use profiles and accessories from the same system

Technical

Closer look

Detailed product imagery is being prepared.

In preparation

Specifications

Technical data

Values below are stated only where the supplied datasheet or Jawdah's verified product data names this item. Anything else is confirmed with the quotation.

Stud 40 – Partition Metal Profile: recorded data
PropertyValueSource
Size (product list)40Jawdah product list
Section (datasheet)35x40x34 mmDatasheet
Steel thickness0.35 up to 0.9 mm; other thicknesses on requestDatasheet
MaterialHot-dip galvanised steel complying with ASTM A653MDatasheet
Standard length3000 mmDatasheet
Fire (raw material)BS 476 Part 6 – 1989; surface flame spread Class 1, BS 476 Part 7 – 1997Datasheet
Humidity (raw material)According to EN ISO 6270-2Datasheet

Key facts

  1. Stud 40 is listed under Jawdah Drywall Solutions, Partition Metal Profiles.
  2. Role: the vertical member of a drywall partition that carries the boards on both faces.
  3. Datasheet section for this size: 35x40x34 mm.
  4. Profile material: hot-dip galvanised steel, ASTM A653M; length 3000 mm.
  5. Other sizes listed: 50, 64, 70, 73, 75, 90, 100, 123, 150.

RFQ / BOQ checklist

  • Profile and size (Stud 40)
  • Steel thickness
  • Length and quantity
  • Board type and layers the system carries
  • Accessories needed (clips, rods, anchors, screws)
  • Project location and delivery date

Resources

Further chapters in preparation

In preparation
  • Technical resources

    Technical documentation is being prepared for this product.

  • Projects using this product

    Project references are being prepared.

  • Compatible systems

    Information on compatible systems for this product is being prepared.

Our technical team can share the current information on request.Ask the technical team

FAQ

Frequently asked questions

  • Jawdah's data sheet lists Stud 40 as a 35x40x34 mm section in hot-dip galvanised steel complying with ASTM A653M.

  • Yes. The product list runs from 40 up to 150, so Stud 40 is the narrowest option. Stud 50 is the next listed size.

  • Jawdah's product list includes a Track 42 in the track range. Confirm the stud and track pairing, and the steel thickness, with the quotation.

Next step

Request a quotation for Stud 40

Send the size, quantities and project location. The Jawdah team confirms the technical data for your order and replies with a quotation.